Thermo Scientific Evolution One Series User Manual Download | Manualshive

Page: 30 / 42

background image

2

Evolution One Series Spectrophotometers

Installing and Removing Accessories

16

Evolution One Series Spectrophotometer User Guide

Thermo Scientific

Related Topics

Rectangular Reference Cell Holder

Spectrophotometer Z-height

Rectangular Reference Cell Holder

For measurements with a reference sample, install a reference cell holder in the reference
position. See

Installing a Reference Cell Holder

.

The standard reference holder accommodates rectangular reference cells with these
pathlengths: 10 mm, 20 mm, 40 mm, 50 mm and 100 mm.

Related Topics

10 mm Rectangular Sample Cell Holder

Installing a Manual Accessory

Manual sampling accessories are mounted on a common baseplate. The kinematic mount
ensures correct alignment of the accessory within the instrument.

It is not necessary to power off the instrument while installing or removing a
manual accessory.

«
...
28
29
30
31
32
...
»

Summary of Contents for Evolution One Series











































Reviews:

No comments

Related manuals for Evolution One Series

Brand: Badger Meter Pages: 47

Brand: M-system Pages: 16

Brand: M-system Pages: 25

Brand: Omicron Lab Pages: 33

Brand: Omicron Lab Pages: 21

Brand: Omicron Lab Pages: 22

Brand: Vectornav Pages: 114

HYGRASREG KH-30

Brand: S+S Regeltechnik Pages: 16

Brand: X-Rite Pages: 45

Brand: X-Rite Pages: 22

Brand: Jula Pages: 9

LISST-PORTABLE XR

Brand: Sequoia Pages: 41

Brand: ACE INSTRUMENTS Pages: 6

Brand: X-Rite Pages: 130

Brand: Hanna Instruments Pages: 28

Brand: Omega Pages: 13

Brand: Polimaster Pages: 24

Brand: Kane Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands