Thermo Scientific Evolution One Series User Manual Download

Page: 36 / 42

Evolution One Series Spectrophotometers

Installing and Removing Accessories

Evolution One Series Spectrophotometer User Guide

Thermo Scientific

Related Topics

Installing a Smart Accessory

Installing a Manual Accessory

Installing a Reference Cell Holder

Installing a Reference Cell Holder

To install a reference cell holder

1. Open the reference compartment cover. See

Opening and Closing the Sample and

Reference Compartment Doors

2. Grasp the cell holder by the handle and lower it into the reference compartment.

3. Insert the pin in the alignment hole and press the holder in place.

4. Close the reference compartment cover.

For descriptions of the available reference holders, see

Reference Cell Holders

or search for that

name in the Insight Pro Help system.

Note

Ensure the tubing does not obstruct the light beam or prevent the sample

compartment door from closing. If necessary, secure the tubing using the
supplied clips.

Handle

Summary of Contents for Evolution One Series











































Search results

Summary of Contents for Evolution One Series

Reviews:

Related manuals for Evolution One Series

Brands by name

Popular brands

Thermo Scientific Evolution One Series, User Manual

Search results

Summary of Contents for Evolution One Series

Reviews:

Related manuals for Evolution One Series

Brands by name

Popular brands