Thermo Scientific Evolution One Series User Manual Download | Manualshive

Page: 32 / 42

background image

2

Evolution One Series Spectrophotometers

Installing and Removing Accessories

18

Evolution One Series Spectrophotometer User Guide

Thermo Scientific

Related Topics

Installing a Liquid Thermostatted Accessory

Installing a Smart Accessory

Installing a Reference Cell Holder

Installing a Smart Accessory

Smart Accessories include cell changers and sample holders that feature auto recognition,
smart alignment and serial number reporting. Smart Accessories ensure software methods are
properly configured.

These accessories install in the sample compartment. A connector under the accessory
baseplate provides data communication and power.

It is not necessary to power off the instrument while installing or removing a Smart Accessory.

Sample compartment top view

To install a Smart Accessory

1. Open the sample compartment door. See

Opening and Closing the Sample and

Reference Compartment Doors

2. Remove the sample compartment front panel. See

Sample Compartment Front Panel

.

3. Remove any cell holder or accessory. See

To remove a Smart Accessory

.

Alignment pins

Toggle

B

A

Smart Accessory connector

Alignment pins

«
...
30
31
32
33
34
...
»

Summary of Contents for Evolution One Series











































Reviews:

No comments

Related manuals for Evolution One Series

Brand: Campbell Pages: 22

Brand: Campbell Pages: 32

Brand: Campbell Pages: 40

CR3000 Micrologger

Brand: Campbell Pages: 12

Brand: R.M. Young Pages: 8

Brand: Campbell Pages: 21

Brand: Quantel Pages: 2

Brand: Harley Benton Pages: 28

Brand: OHAUS Pages: 19

Brand: OHAUS Pages: 54

Brand: Zenner Pages: 2

Brand: janitza Pages: 48

Brand: DAKOTA ULTRASONICS Pages: 50

Brand: Jamar Pages: 4

Brand: janitza Pages: 85

Brand: S+S Regeltechnik Pages: 32

Brand: OHAUS Pages: 84

Brand: RS PRO Pages: 41

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands