Thermo Scientific Barnstead EASYpure RODI 1332 Series Operation Manual And Parts List Download Page 5

Page: 5 / 60

To avoid personal injury:

1. Do not use in the presence of flammable or

combustible materials; fire or explosion may

result. This device contains components which

may ignite such materials.

2. Do not use in the presence of highly corrosive

substances such as bleach or acid baths; fire

may result.

3. This device is to be used with water feeds only.

Cleaning agents must be used in compliance

with instructions in this manual. Failure to com-

ply with the above could result in explosion

and personal injury.

4. Avoid splashing cleaning solutions on clothing

or skin.

5. Ensure all piping connections are tight to avoid

chemical leakage.

6. Ensure adequate ventilation.

7. Carefully follow manufacturerʼs safety instruc-

tions on labels of chemical containers and

material safety data sheets.

8. Depressurize system prior to opening cartridge

access door or removing top cover.

9. This unit is equipped with an ultraviolet lamp.

Ultraviolet radiation is harmful to the eyes and

skin. Do not observe the lamp directly while it

is illuminated.

10. Do not operate unit with door open. Inlet pres-

sure may force RO prefilter out of position.

11. Refer servicing to qualified personnel.

AFETY

NFORMATION

Summary of Contents for Barnstead EASYpure RODI 1332 Series





























































Search results

Summary of Contents for Barnstead EASYpure RODI 1332 Series

Reviews:

Related manuals for Barnstead EASYpure RODI 1332 Series

Brands by name

Popular brands

Thermo Scientific Barnstead EASYpure RODI 1332 Series, Operation Manual And Parts List

Search results

Summary of Contents for Barnstead EASYpure RODI 1332 Series

Reviews:

Related manuals for Barnstead EASYpure RODI 1332 Series

Brands by name

Popular brands