Theben FCA 2 Page 37 Manual Download

Page: 37 / 89

Fan Coil Actuator FCA 2

Updated: Feb-16 (subject to changes) Page

3.4.6 Parameter page Additional relay

Table 25

Designation

Values

Meaning

Switching on the additional
relay

Via object

The additional relay is only
controlled from outside via
the bus (see object 5)

If heating is required

The additional relay is
switched on as soon as the
heating actuating value is
above 0 %.

If cooling is required

The additional relay is
switched on as soon as the
cooling actuating value is
above 0 %.

Combined with heating valve

The additional relay only
switches on when the heating
valve is actually opened*.

Combined with cooling valve

The additional relay only
switches on when the cooling
valve is actually opened*.

Transmission of additional
relay status every

do not send cyclically
3 min
5 min
10 min
15 min
20 min
30 min
60 min

Cyclical transmission time for
the additional relay status.

With the setting

Switching on

the additional relay=

via object

, the status is not

transmitted.

* With an adjusted valve characteristic, the valve can remain closed with a low actuating value.

Summary of Contents for FCA 2


























































































Search results

Summary of Contents for FCA 2

Reviews:

Related manuals for FCA 2

Brands by name

Popular brands

Theben FCA 2, Manual

Search results

Summary of Contents for FCA 2

Reviews:

Related manuals for FCA 2

Brands by name

Popular brands