Thames & Kosmos 623715 Experiment Manual Download Page 58 | Manualshive

Page: 58 / 68

background image

5

6

7

8

9

5. On the other side of the base plate, mount another two short frames
(3) with three anchor pins (26) on top and four on the side.

9. For the front framework, you will need to mount two short rods (4)
onto the anchor pins on the top of the front frames. Also mount a short
rod (4) on the rear frames.

7. Now adjust the two sprocket wheels so that they are aligned and
attach a chain made out of 42 chain links (29).

6. A long axle shaft (16) with small gear wheel (8) and small sprocket
wheel (9) goes through the fourth hole from the top in the frames that
have just one anchor pin on the top.

8. Insert a small axle shaft (18). Attach a medium gear wheel (7) to one
side, and the spool with cord and hook (28) to the other.

56

«
...
56
57
58
59
60
...
»

Summary of Contents for 623715





































































Reviews:

No comments

Related manuals for 623715

Brand: K'Nex Education Pages: 4

Brand: GREAT PLANES Pages: 35

Brand: BUSCH Pages: 8

Brand: Multiplex Pages: 17

Midwest FreightReady-to-Run Set

Brand: Lionel Pages: 16

Brand: E sky Pages: 32

Brand: Jamara Pages: 20

Brand: Radio Shack Pages: 9

Brand: LEGO Pages: 84

SPEED MASTER TG511

Brand: THINK GIZMOS Pages: 6

Brand: bewello Pages: 12

Brand: Phoenix Model Pages: 15

Brand: Z-Stuff for Trains Pages: 4

RailKing Steel Arch Bridge

Brand: MTHTrains Pages: 5

SCP-09 Flying Saucer Plus

Brand: Elenco Electronics Pages: 4

Inflatable Santa 5 m

Brand: RUSTA Pages: 8

Extra 260-EP BH55

Brand: Black Horse Model Pages: 20

Brand: Fisher-Price Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands