4-1. FUEL INJECTION SYSTEM
4-1-37
4) Disconnect the TP sensor coupler.
5) Check the continuity between W/Br wire and
ground.
6) Also, check the continuity between W/Br wire
and Gr/R wire
C. If the sound is not heard from the tester, the
circuit condition is OK.
7) Disconnect the ECU coupler.
8) Check the continuity between W/Br wire and
terminal 31.
9) Also, check the continuity between Y/B wire
and terminal .
TPS lead wire continuity: Continuity (sound)
Is the continuity OK?
YES Go to step 1 and step 2
NO
Y/B wire or Gr/R wire open, or Gr/R
wire shorted to ground
10) After repairing the trouble, clear the DTC
using Diagnosis tool.
Step 2
1) Turn the ignition switch OFF.
2) Disconnect the TP sensor coupler.
3) Check the continuity between W/Br wire and
ground.
TP sensor continuity:
∞ Ω (Infinity)
(White/Brown
– Ground)
4) If OK, then measure the TP sensor
resistance at the terminals (between Bottom
and Center pin).
5) Turn the throttle grip and measure the
resistance.
TP sensor resistance
Throttle valve is closed: Approx. 1.1 kΩ
Th
rottle valve is opened: Approx. 4.4 kΩ
6) If OK, then measure the TP sensor
resistance at the terminals (between Upper
and Center pin).
TP sensor resistance: Approx. 4.66 kΩ
(Upper pin
– Center pin)
31
Summary of Contents for BLADE 500
