TFS NTP80plus Reference Manual Download Page 7 | Manualshive

Page: 7 / 57

background image

MANUAL P/N 900000165 REV H

7

1

Introduction

1.1

Introduction to the NTP80plus Multiport Time Server

Congratulations on the purchase of your Time & Frequency Solutions NTP-Multiport Time
Server, Model Number NTP80plus.

This manual shows you how to install, configure and operate your NTP80plus to provide an NTP
time server for your network. Once up and running the NTP80plus will provide accurate time
synchronisation for your computer clients to within milliseconds on a LAN and tens of
milliseconds over a WAN,

Prior to installing the NTP80plus please read the site preparation section first to ensure the
smooth operation of your NTP80plus when it is installed. Then follow the quick setup guide to
get your NTP80plus up and running. The remaining sections give more details on the
configuration and operation of the NTP80plus.

Feedback

At Time & Frequency Solutions we pride ourselves on a quality product and our superior
service. If you wish to comment on this, or provide improved feedback on this manual then
please feel free to contact us. You may email us at

[email protected]

or contact as at the

following -

Time & Frequency Solutions Ltd

25 Eastways

Witham

Essex

CM8 3AL

United Kingdom

Tel +44 (0) 1376 514114

Fax +44 (0) 1376 516116

«
...
5
6
7
8
9
...
»

Summary of Contents for NTP80plus


























































Reviews:

No comments

Related manuals for NTP80plus

Brand: NAIM Pages: 16

Enterprise Server

Brand: Blackberry Pages: 88

NetScaler MPX 25100 40G

Brand: Citrix Pages: 15

SUPERO SuperServer 1018L-MP

Brand: Supermicro Pages: 104

Brand: IOGear Pages: 44

Brand: 3onedata Pages: 3

Brand: ABB Pages: 9

Brand: ABB Pages: 68

Brand: Red Hat Pages: 120

Brand: Black Box Pages: 4

Brand: Black Box Pages: 12

m330 media server

Brand: Wadia Pages: 24

Brand: Planet Networking & Communication Pages: 67

Brand: Planet Networking & Communication Pages: 76

Brand: Z Microsystems Pages: 21

Brand: Inspur Pages: 2

AS1021M-UR Plus

Brand: Supero Pages: 104

Brand: Supero Pages: 102

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands