background image

 

Confidential and Proprietary 

 

 2.3 

Rev. 10.06 

 

Texwrap 

 

“Built-Better/Backed-Better Warranty

” 

 

All Texwrap manufactured components are warranted against defects in design, material and 
workmanship for a period of three (3) years- unlimited cycles. All purchased components are 
warranted for a period of one year. Warranty is transferrable for the life of the Warranty 
beginning with date of shipment to the original purchaser's facility. Warranty does not cover 
the replacement of consumable/wear items (sealing blades, sealing pads, tape, belts, etc), 
routine maintenance, or alignments. 
 
Texwrap will, at their discretion, repair or replace a defective component at no charge 
including UPS ground transportation. Field technician labor is typically handled on 
warranted items by local Texwrap distributors on a billable basis.  Contact your local 
Texwrap distributor for their warranty claim procedure and policies. 
 
This warranty will become null and void if it is determined by Texwrap that: 

    - the equipment is misused, abused or neglected in any way. 
    - the equipment is altered or modified without prior written approval from Texwrap. 

 
Texwrap does not warrant that the equipment conforms to any insurance regulation, electrical 
or safety code (with the exception of panels containing UL stickers, which meet UL codes).  
The purchaser assumes liability for compliance with all applicable statutes, codes and 
regulations whether federal, state or local. 
 
This limited warranty applies only to the repair or replacement of defective parts. Warranty 
does not cover replacement parts not purchased from Texwrap. 

 

For any replacement part shipped under warranty, the defective part must be returned to 
Texwrap by a Texwrap distributor within 30 days for examination. If determined to be 
defective, a credit will be issued. If the part is determined not to be defective, the part will be 
returned to shipper and no credit issued.  Credits will not be issued for parts after 30 days.  
 
Please note: A Return Authorization (RA) number must be obtained from the Parts 
Department prior to shipment of a defective part to Texwrap.  
 

Summary of Contents for 2219 Series








































































Reviews: