Odyssey X
Installation Manual
INS627-2
13
The unit incorporates software which disables the strobe whilst the tamper switch remains open. This is a safety feature and cannot be
disabled.
The piezo drive produces high voltages when the siren is sounding. While not directly hazardous, these voltages will cause discomfort
and should be avoided, particularly when using tools or a ladder.
The piezo transformer TF1 and surrounding components will be hot during and after sounding. While not directly hazardous, contact when
hot will cause discomfort and should be avoided, particularly when using tools or a ladder.
Failure to observe the following precautions regarding the batteries could lead to the danger of heating, ignition or explosion:
•
Always observe local regulations
•
Do not throw into a fire
•
Do not overcharge
•
Do Not Short Circuit
•
Replace only with the same type
•
Do not heat
•
Do Not Reverse Charge
•
Do not disassemble
Technical Specification
Environmental
Electrical Wired Units
Volume (SAB mode at 13.7VDC)
Supply Voltage
12-16 VDC (13.7 nominal)
X-W
X-E & X-EB
105dB Peak at 1m (A Weighting, 90
°
)
109dB Peak at 1m (A Weighting, 90
°
)
Current Drain (typical at 13.7VDC)
X & X-B Models:
115dB Peak at 1m (A Weighting, 90
°
)
Quiescent:
18mA
With backlight 58mA
Acoustic Output
Varying Sound Output
Strobe:
100mA
Cut-Off Time:
≤
15 minutes
Sounder
SAB
LC
SCB
Waterproof Coating:
Conformal
X-E Models:
285mA
160mA
30mA
X-BE
325mA
200mA
70mA
X Models:
405mA
190mA
30mA
Environmental Protection
X-B Models
445mA
230mA
70mA
X-E & X-BE Models:
Weather Resistant
Standby Battery
X-W, X & X-B Models:
Type:
NiMh Stack
Operating Temperature:
-25
°
C (-13
°
F) to +55
°
C (+131
°
F)
Voltage:
7.2VDC (nominal)
Storage Temperature:
-25
°
C (-13
°
F) to +60
°
C (+140
°
F)
Capacity:
250mAh
EMC Environment:
Residential / Commercial /Light Industrial
/ Industrial
Flash Tube:
1Ws Xenon
Physical
Flash Rate:
1Hz (typical)*
Material
Discharge Time (
≤
60VDC):
≤
180 seconds
Backplate All Models
3mm Polycarbonate
Comfort LEDs
Covers All Models
3mm Polycarbonate/3mm PMMA
High Intensity
White
Tamper Detection
Brightness:
100mcd (typical)
All models
Wall & Inner cover
Flash Rate (tamper
secure):
1Hz alternating
(typical)
Lid Dimensions (h x w x d)
Electrical Wireless
X3
290mm x 276mm x 58mm
Supply Voltage:
12V DC
X1
290mm x 186mm x 58mm
Battery Type:
8 x Lithium type
AA 1.5V
Module Dimensions (h x w x
d)
287mm x 170mm x 51
High Power LED Strobe:
320lm
Flash Rate:
1Hz (typical)*
Packed Weight
Module only (Not X-W)
791g (28oz) approx>
Comfort LEDs:
Module only Odyssey X-W
991g (35oz) approx>
X1 Cover
310g (11oz) approx.
Brightness:
100mcd (typical)
X3 Cover
613g (22oz) approx.
Flash Rate (tamper secure):
1/4 sec flash at 5
sec intervals
alternating
(typical)
Wireless Frequency:
868.0MHz
–
868.6MHz
* Wired Units
The flash rate will reduce to 0.125Hz after flashing for one hour (1 flash every 8 seconds). This is a software feature to reduce power consumption
and cannot be disabled.
*Wireless Units
The flash rate will reduce to 0.125Hz after flashing for 20 minutes (1 flash every 8 seconds). This is a software feature to reduce power
consumption and cannot be disabled. After 10 days the strobe is cancelled completely. Turning the strobe off then on again will resume normal operation. In
extreme conditions where the temperature is likely to exceed the stated maximum avoid direct sunlight.
Total alarm current = Qui Sounder current.
