17
Cleaning the tiller
The tiller should be cleaned after use. Use a garden
hose to wash off soil and dirt. Remove any grass, etc.
from the rotor shaft. The chassis number should only be
cleaned with a damp cloth to avoid unnecessary wear.
Avoid using a high-pressure washer during cleaning.
Changing the oil
The oil should initially be changed after the first 5 hours
of use, and thereafter once per year.
1. Let the motor run for 5 minutes to heat up the oil.
This allows the oil to run more freely and makes for
a more complete oil change.
2. After 5 minutes, stop the motor. Remove the spark
plug cap. Drain the oil by unscrewing the sump
plug. Remember to drain the oil into a container of
sufficient capacity. NB: The motor must not be
tipped backwards more than 45 degrees.
3. Screw the sump plug back in and pour new oil into
the motor. Do this by removing the dipstick and
pouring in the recommended quantity of oil.
4. Refit the spark plug cap.
Alternatively, use an oil extractor kit:
1. Suck the oil up through the oil filler hole using the
syringe. Use the hose to reach the sump.
2. Transfer the used oil to the container.
3. Fill the engine with new SAE-30 oil.
4. Check the oil level reaches the edge of the filling
hole (Fig. 21).
Remember to dispose of used oil in a safe way.
Oil and oil extractor kit are not included
Air filter maintenance
Please inspect and clean the air filter on a regular
basis. If the filter has not been cleaned for a longer
period, this will have influence on the engines power
take-off and the exhaustion.
1. Clean around the air filter before it is removed.
2. Carefully remove the paper filter and check it.
Brush it with a soft brush. If it is very dirty, it must
be changed. Take care that no dirt gets into the
intake of the engine.
3. Wash the black foam element on the right side in
warm soapy water.
4. Press the water out of the foam element and let it
dry. Put a few drops of SAE-30 oil on the filter to
moisten it lightly with oil. Carefully squeeze out any
surplus oil. Remount the element.
5. Check that all parts are fitted correctly and the
cover closed as shown in the picture.
See the engine user manual for further information.
Spark plug maintenance
•
Remove the spark plug cap.
•
Brush away any dirt and deposit of the spark plug.
•
Loosen the spark plug using a spark plug socket.
•
Check the insulation is intact.
•
Clean the spark plug using a wire brush.
•
Measure the electrode gap 0.7–0.8 mm. Avoid
damaging the electrode.
•
If it is damaged, replace it with a new one.
•
Refit the spark plug.
•
Refit the spark plug cap.
Storage
•
If the machine is likely to be stored unused for
prolonged periods, follow the instructions below.
This will ensure longer machine lifetime.
•
Use a garden hose to wash off soil and dirt.
Remove any grass, etc. from the rotor shaft. The
chassis number should only be cleaned with a
damp cloth to avoid unnecessary wear. Avoid using
a high-pressure washer during cleaning.
•
Wipe the tiller with a damp cloth so that all surfaces
are clean. Wipe the surfaces down with an oily
cloth to prevent rust.
•
Always store the machine in a dry, clean location.
Troubleshooting
The motor will not start
1. Check the fuel control is set to level “4”.
2. Check the spark plug.
3. Check there is fresh gas in the tank.
4. See separate motor instructions for further
troubleshooting.
The motor is not running smoothly
1. Ensure the choke is completely turned off.
2. Check there is fresh gas in the tank.
The blades will not rotate
1. Check for stones lodged between the blades.
2. Release any stones by removing the blades.
3. Check the cables are in good working order and
fitted correctly.
4. Check the belt is in good working order and fitted
correctly.
5. Ensure the belt tensioner is adjusted correctly.
The blades will not stop
1. Stop the engine and contact your dealer.
2. Check that he belt pulley is adjusted correctly.
Engine will not stop
1. Adjust the throttle cable
Noise, vibration and precautionary measures
1. Long-term exposure to noise levels exceeding 85
dB (A) are damaging. Always use ear defenders
when the machine is being used.
2. Reduce the running speed of the motor to reduce
vibration and noise levels.
3. To reduce noise levels further, only use the
machine in an open environment.
4. Vibrations can be reduced further by holding the
handle firmly.
5. To avoid disturbing others, the machine should only
be used during the daytime.
6. Always wear close-fitting work clothes, hard-
wearing work gloves, ear defenders and non-slip
boots with steel toecaps.
7. Take a 30-minute break every 2 working hours.
8. A worn belt has to be replaced/ serviced by a
authorized dealer
