Troy-Bilt OEM-290-263 Operator'S Manual Download Page 1 | Manualshive

Page: 1 / 8

Troy-Bilt OEM-290-263 Operator'S Manual Download Page 1

Power Rake Attachment

Model 290-263-081 / OEM-290-263

TILLER/CULTIVATOR

Introduction

Please check the contents of the shipping carton against the
Parts List below. If any parts are missing or damaged, be
sure to contact your TROY-BILT Dealer or the Factory.

To help ensure proper installation and safe operation of this
attachment, read and carefully follow these instructions.

®

CAUTION

TO AVOID INJURY:
• Read the Owner/Operator Manual.
• Know the location and function of all controls.
• Keep all safety devices and shields in place.
• Never allow children or uninstructed adults to

operate the machine.

• Shut off engine and disconnect spark plug wire

before unclogging tines or making repairs.

• Keep bystanders away from machine.
• Keep away from rotating parts.

Safety

Before installing or using this attachment, carefully review
the “Safety Rules” and “Operation” instructions in your
Tiller/Cultivator Owner/Operator Manual. Doing so will
refresh your memory concerning safe operating practices
that must be followed at all times.

Tools/Supplies Needed for Installation

• No tools are required.
• Fine-grade sandpaper (to remove rust from tine shaft).
• General purpose oil (to lubricate tine shaft).

Figure 1

Parts List - see Figure 1

Ref. #

Part #

Description

Qty.

1

—

Rake Assembly – left side................. 1

2

—

Rake Assembly – right side .............. 1

3 1915063

Debris Shield .................................... 1

4 GW-H214187

Mounting Strap................................. 1

5 GW-H214186

“S” Hook........................................... 2

6 1983648

1-

1

⁄

4

"long Spacer................................ 2

1

3

2

5

4

6

Thank you for ordering this attachment for your Tiller/Cultivator. We know that it will per-
form to your complete satisfaction if installed and used properly. Refer to the information
below that applies to the attachment you ordered and check the parts
shipped to you. If you have any questions concerning the use of
your POWER RAKE, be sure to contact us for assistance.

THANK

YOU!

1
2
3
...
»

Summary of Contents for OEM-290-263









Reviews:

No comments