manualshive.com logo in svg

Texas Instruments TMS320x2823x, Reference Manual

Share
Download
Texas Instruments TMS320x2823x Reference Manual Download Page 107

www.ti.com

Registers

Table 40. Trip-Zone Enable Interrupt Register (TZEINT) Field Descriptions (continued)

Bits

Name

Value

Description

1

CBC

Trip-zone Cycle-by-Cycle Interrupt Enable

0

Disable cycle-by-cycle interrupt generation.

1

Enable interrupt generation; a cycle-by-cycle trip event will cause an EPWMx_TZINT PIE
interrupt.

0

Reserved

Reserved

Figure 83. Trip-Zone Flag Register (TZFLG)

15

8

Reserved

R-0

7

3

2

1

0

Reserved

OST

CBC

INT

R-0

R-0

R-0

R-0

LEGEND: R/W = Read/Write; R = Read only; -n = value after reset

Table 41. Trip-Zone Flag Register (TZFLG) Field Descriptions

Bits

Name

Value Description

15-3

Reserved

Reserved

2

OST

Latched Status Flag for A One-Shot Trip Event

0

No one-shot trip event has occurred.

1

Indicates a trip event has occurred on a pin selected as a one-shot trip source.

This bit is cleared by writing the appropriate value to the TZCLR register.

1

CBC

Latched Status Flag for Cycle-By-Cycle Trip Event

0

No cycle-by-cycle trip event has occurred.

1

Indicates a trip event has occurred on a pin selected as a cycle-by-cycle trip source. The
TZFLG[CBC] bit will remain set until it is manually cleared by the user. If the cycle-by-cycle trip
event is still present when the CBC bit is cleared, then CBC will be immediately set again. The
specified condition on the pins is automatically cleared when the ePWM time-base counter
reaches zero (TBCTR = 0x0000) if the trip condition is no longer present. The condition on the
pins is only cleared when the TBCTR = 0x0000 no matter where in the cycle the CBC flag is
cleared.

This bit is cleared by writing the appropriate value to the TZCLR register.

0

INT

Latched Trip Interrupt Status Flag

0

Indicates no interrupt has been generated.

1

Indicates an EPWMx_TZINT PIE interrupt was generated because of a trip condition.

No further EPWMx_TZINT PIE interrupts will be generated until this flag is cleared. If the
interrupt flag is cleared when either CBC or OST is set, then another interrupt pulse will be
generated. Clearing all flag bits will prevent further interrupts.

This bit is cleared by writing the appropriate value to the TZCLR register ().

Figure 84. Trip-Zone Clear Register (TZCLR)

15

8

Reserved

R-0

7

3

2

1

0

Reserved

OST

CBC

INT

R-0

R/W-0

R/W-0

R/W-0

LEGEND: R/W = Read/Write; R = Read only; -n = value after reset

107

SPRUG04A – October 2008 – Revised July 2009

TMS320x2833x, 2823x Enhanced Pulse Width Modulator (ePWM) Module

Submit Documentation Feedback

© 2008–2009, Texas Instruments Incorporated

Summary of Contents for TMS320x2823x




















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands