Texas Instruments Sitara AM1335 Series Manual Download Page 16 | Manualshive

Page: 16 / 39

background image

Usage Notes and Known Design Exceptions to Functional Specifications

–

Clear the TIMER5 interrupt by setting bit 2 of the TIMER5 IRQSTATUS register
located at 0x4804_6028 to 1b.

–

Clear the TIMER6 interrupt by setting bit 2 of the TIMER6 IRQSTATUS register
located at 0x4804_8028 to 1b.

•

Disable all CPSW interrupts by clearing the C0_xx_EN field in the respective
C0_RX_EN/C0_TX_EN register.

•

Acknowledge the interrupt by writing the appropriate RX or TX vector to the
CPDMA_EOI_VECTOR register.

•

Process all received or transmitted packets.

•

Enable the desired CPSW interrupts in the C0_xx_EN field in the respective
C0_RX_EN/C0_TX_EN register.

16

SPRZ360F – October 2011 – Revised November 2013

Sitara™ AM335x ARM

®

Cortex™-A8 Microprocessors (MPUs) (Silicon

Revision 2.1, 2.0, 1.0)

Submit Documentation Feedback

Copyright © 2011–2013, Texas Instruments Incorporated

«
...
14
15
16
17
18
...
»

Summary of Contents for Sitara AM1335 Series








































Reviews:

No comments

Related manuals for Sitara AM1335 Series

Vb-C60 - Ptz Network Camera

Brand: Canon Pages: 30

Fieldpoint cFP-RTD-124

Brand: National Instruments Pages: 15

Brand: Telit Wireless Solutions Pages: 113

UM10301 PCA8565

Brand: NXP Semiconductors Pages: 54

Brand: Idis Pages: 20

UniFi LED ULED-AT

Brand: Ubiquiti Pages: 16

NetVanta Serial Dial Backup Interface Module (DIM) none

Brand: ADTRAN Pages: 2

Brand: HMS Pages: 18

Brand: WIN Enterprises Pages: 25

Brand: Boser Pages: 82

PC/104-PCMCIA-1

Brand: Kontron Pages: 20

Brand: silicom Pages: 16

Brand: National Datacomm Pages: 62

Brand: ICS Advent Pages: 26

Brand: LinMot Pages: 62

Brand: Aegis Pages: 7

ControlWave Remote Ethernet I/O

Brand: Emerson Pages: 3

Brand: Emerson Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands