Texas Instruments OMAP36 Series Technical Reference Manual Download Page 1941 | Manualshive

Page: 1941 / 3738

background image

Public Version

www.ti.com

Display Subsystem Register Manual

Table 7-414. DSI_VM_TIMING6

Address Offset

0x0000 008C

Physical Address

0x4804 FC8C

Instance

DSI_PROTOCOL_ENGINE

Description

VIDEO MODE TIMING REGISTER This register defines the video mode timing.

Type

RW

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

BL_HS_INTERLEAVING

BL_LP_INTERLEAVING

Bits

Field Name

Description

Type

Reset

31:16

BL_HS_INTERLEAVING

Defines the number of TxByteClkHS clock cycles that

RW

0x0000

can be used for interleaving high-speed command mode
packet into Video Mode stream during blanking periods
during VSA, VBP, VFP periods inside one video frame
on PPI link.
The supported values are from 0 to 65535.

15:0

BL_LP_INTERLEAVING

Defines the maximum number of bytes for Low Power

RW

0x0000

command mode packets that can be sent on PPI link
during blanking periods during VSA, VBP or VFP periods
inside one video frame on PPI link.
The supported values are from 0 to 65535

Table 7-415. Register Call Summary for Register DSI_VM_TIMING6

Display Subsystem Environment

•

Video Port Used for Video Mode

Display Subsystem Functional Description

•

HS Command Mode Interleaving Programming Model

:

•

LP Command Mode Interleaving Programming Model

:

Display Subsystem Basic Programming Model

•

Display Subsystem Register Manual

•

DSI Protocol Engine Register Mapping Summary

Table 7-416. DSI_VM_TIMING7

Address Offset

0x0000 0090

Physical Address

0x4804 FC90

Instance

DSI_PROTOCOL_ENGINE

Description

Defines the maximum number of bytes of Low Power command mode packets that can be sent on PPI
link during blanking periods during VSA, VBP or VFP periods inside one video frame on PPI link. The
supported values are from 0 to 65535

Type

RW

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

ENTER_HS_MODE_LATENCY

EXIT_HS_MODE_LATENCY

Bits

Field Name

Description

Type

Reset

31:16

ENTER_HS_MODE_

Defines the number of TxByteClkHS clock cycles necessary

RW

0x0000

LATENCY

for entering to HS mode. It corresponds to the delay in
number of HS clock cycles from assertion of TxRequestHS
signal to 1 until assertion of TxReadyHS signal to 1.
The supported values are from 0 to 65535 .

1941

SWPU177N – December 2009 – Revised November 2010

Display Subsystem

Copyright © 2009–2010, Texas Instruments Incorporated

«
...
1939
1940
1941
1942
1943
...
»

Summary of Contents for OMAP36 Series



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP36 Series

All in One Printer

Brand: Baracoda Pages: 42

Brand: IEI Technology Pages: 19

Brand: IEI Technology Pages: 87

Brand: IEI Technology Pages: 3

Brand: Yaesu Pages: 2

Procont LMC-008-IO

Brand: janitza Pages: 28

Brand: ACTi Pages: 12

Brand: PairGain Pages: 80

XC-16CH-NVR-4TB

Brand: Xyclop Pages: 19

Brand: Patton electronics Pages: 8

Brand: LevelOne Pages: 49

POD-51EH-C541U-12

Brand: IceTech Pages: 8

Brand: Intel Pages: 154

Acme Packet 3900

Brand: Oracle Pages: 70

Protection Board R0E330850ACBP0

Brand: Renesas Pages: 8

Brand: ZALMAN Pages: 9

Brand: IEI Technology Pages: 116

Brand: SeaLevel Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands