Texas Instruments OMAP36 Series Technical Reference Manual Download

Page: 1932 / 3738

Public Version

Display Subsystem Register Manual

www.ti.com

Table 7-391. Register Call Summary for Register DSI_TIMING2

Display Subsystem Functional Description

•

•

Display Subsystem Use Cases and Tips

•

Configure DSI Timing and Virtual Channels

[6]

•

Configure DSI Protocol Engine

[7] [8] [9] [10] [11] [12]

Display Subsystem Register Manual

•

DSI Protocol Engine Register Mapping Summary

[13]

Table 7-392. DSI_VM_TIMING1

Address Offset

0x0000 0060

Physical Address

0x4804 FC60

Instance

DSI_PROTOCOL_ENGINE

Description

VIDEO MODE TIMING REGISTER This register defines the video mode timing.

Type

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

HSA

HFP

HBP

Bits

Field Name

Description

Type

Reset

31:24

HSA

Defines the horizontal Sync active period used in video mode in

0x00

number of byte clock cycles (TxByteClkHS)
The supported values are from 0 to 255.

23:12

HFP

Defines the horizontal front porch used in video mode in number of

0x000

byte clock cycles (TxByteClkHS)
The supported values are from 0 to 255

11:0

HBP

Defines the horizontal back porch used in video mode in number of

0x000

byte clock cycles (TxByteClkHS)
The supported values are from 0 to 255

Table 7-393. Register Call Summary for Register DSI_VM_TIMING1

Display Subsystem Basic Programming Model

•

•

Display Subsystem Use Cases and Tips

•

Configure DSI Timing and Virtual Channels

[2]

Display Subsystem Register Manual

•

DSI Protocol Engine Register Mapping Summary

[3]

Table 7-394. DSI_VM_TIMING2

Address Offset

0x0000 0064

Physical Address

0x4804 FC64

Instance

DSI_PROTOCOL_ENGINE

Description

VIDEO MODE TIMING REGISTER This register defines the video mode timing.

Type

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

RESERVED

VSA

VFP

VBP

WINDOW_SYNC

1932

Display Subsystem

SWPU177N – December 2009 – Revised November 2010

«
...
1930
1931
1932
1933
1934
...
»

Summary of Contents for OMAP36 Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OMAP36 Series

Reviews:

Related manuals for OMAP36 Series

Brands by name

Popular brands

Texas Instruments OMAP36 Series, Technical Reference Manual

Search results

Summary of Contents for OMAP36 Series

Reviews:

Related manuals for OMAP36 Series

Brands by name

Popular brands