manualshive.com logo in svg

Texas Instruments OMAP36 Series, Technical Reference Manual, Page: 1807 / 3738

Share
Download
Texas Instruments OMAP36 Series Technical Reference Manual Download Page 1807

Public Version

www.ti.com

Display Subsystem Use Cases and Tips

Table 7-106. DSI Complex I/O Registers (continued)

Steps

Register/Bit Field/Programming

Value

Clear all COMPLEXIO IRQ status.

DSI_COMPLEXIO_IRQSTATUS

0xC3F39CE7

Disable all COMPLEXIO IRQs.

DSI_COMPLEXIO_IRQENABLE

0x0

Enable interface.

DSI_CTRL

[0] IF_EN

0x1

Disable interface.

DSI_CTRL

[0] IF_EN

0x0

Wait until IF_EN = 0.

DSI_CTRL

[0] IF_EN

Enable the LP clock.

DSI_CLK_CTRL

[20] LP_CLK_ENABLE

0x1

Check whether reset is complete.

DSI_COMPLEXIO_CFG1

[29] RESET_DONE

0x1

Check whether power control is on.

DSI_COMPLEXIO_CFG1

[26:25] PWR_STATUS

0x1

Check whether reset is complete.

DSI_SYSSTATUS

[0] RESETDONE

0x1

7.6.5.1.2.4.2 Configure DSI Timing and Virtual Channels

Table 7-107

lists the steps to configure DSI timing and the virtual channels.

Table 7-107. DSI Timing Registers

Steps

Register/Bit Field/Programming

Value

Determine the number of DSI_FCLK clock

DSI_TIMING1

[12:0]

0x999

cycles for the STOP-STATE counter.

STOP_STATE_COUNTER_IO

Disable the multiplication factor of 4 for the
number of DSI_FCLK clock cycles for the

DSI_TIMING1

[13] STOP_STATE_X4_IO

0x0

STOP-STATE counter.

Disable the multiplication factor of 16 for the
number of DSI_FCLK clock cycles for the

DSI_TIMING1

[14] STOP_STATE_X16_IO

0x0

STOP-STATE counter.

Clear turn-around timer settings.

DSI_TIMING1

[30:16]

0x0000

Determine the number of DSI_FCLK clock

DSI_TIMING2

[12:0] LP_RX_TO_COUNTER

0x0CD

cycles for the LP RX timer.

Disable the multiplication factor of 4 for the
number of DSI_FCLK clock cycles for the LP

DSI_TIMING2

[13] LP_RX_TO_X4

0x0

RX timer.

Enable the multiplication factor of 16 for the
number of DSI_FCLK clock cycles for the LP

DSI_TIMING2

[14] LP_RX_TO_X16

0x1

RX timer.

Determine the number of TxByteClkHS clock

DSI_TIMING2

[12:0] HS_TX_TO_COUNTER

0xFD2

cycles for the HS RX timer.

Disable the multiplication factor of 8 for the
number of TxByteClkHS clock cycles for the

DSI_TIMING2

[13] HS_TX_TO_X8

0x0

HS TX timer.

Enable the multiplication factor of 16 for the
number of TxByteClkHS clock cycles for the

DSI_TIMING2

[14] HS_TX_TO_X16

0x1

HS TX timer.

DDR_CLK_PRE<<8|DDR_CLK_POST

DSI_CLK_TIMING

[31:0]

0x0000 0F0B

Configuration of VC1

Enable the checksum generation for the

DSI_VC1_CTRL[7] CS_TX_EN

0x1

transmit payload.

Enable the ECC generation for the transmit

DSI_VC1_CTRL[8] ECC_TX_EN

0x1

header.

Disable DMA request for TX FIFO.

DSI_VC1_CTRL[23:21] DMA_TX_REQ_NB

0x4

Disable DMA request for RX FIFO.

DSI_VC1_CTRL[29:27] DMA_RX_REQ_NB

0x4

Configuration of VC0

Selects source of data and enable VP_STALL.

DSI_VC0_CTRL[1] SOURCE

0x1

Enable the checksum generation for the

DSI_VC0_CTRL[7] CS_TX_EN

0x1

transmit payload.

1807

SWPU177N – December 2009 – Revised November 2010

Display Subsystem

Copyright © 2009–2010, Texas Instruments Incorporated

Summary of Contents for OMAP36 Series



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments