manualshive.com logo in svg

Tews Technologies TPMC310, User Manual

Share
Download
Tews Technologies TPMC310 User Manual Download Page 14

 

 

TPMC310 User Manual Issue 1.1.5 

Page 14 of 22 

4.2 Local Configuration Register (LCR) 

After reset, the PCI9030 Local Configuration Registers are loaded from the on board serial 
configuration EEPROM. 

PCI Base Address : 

PCI9030 PCI Base Address 0 (PCI Memory Space) (Offset 0x10 in PCI9030 PCI Configuration 
Register Space), or  

PCI9030 PCI Base Address 1 (PCI I/O Space) (Offset 0x14 in PCI9030 PCI Configuration 
Register Space). 

 

Do not change hardware dependent bit settings in the PCI9030 Local Configuration Registers. 

Offset to PCI Base 

Address 

Register 

Value 

0x00 

Local Address Space 0 Range 

0x0FFF_FFF0 

0x04 

Local Address Space 1 Range 

0x0FFF_FE00 

0x08 

Local Address Space 2 Range 

0x0000_0000 

0x0C 

Local Address Space 3 Range 

0x0000_0000 

0x10 

Local Exp. ROM Range 

0x0000_0000 

0x14 

Local Re-map Register Space 0 

0x0000_0001 

0x18 

Local Re-map Register Space 1 

0x0000_1001 

0x1C 

Local Re-map Register Space 2 

0x0000_0000 

0x20 

Local Re-map Register Space 3 

0x0000_0000 

0x24 

Local Re-map Register ROM 

0x0000_0000 

0x28 

Local Address Space 0 Descriptor 

0x1500_C0A0 

0x2C 

Local Address Space 1 Descriptor 

0x1502_4120 

0x30 

Local Address Space 2 Descriptor 

0x0000_0000 

0x34 

Local Address Space 3 Descriptor 

0x0000_0000 

0x38 

Local Exp. ROM Descriptor 

0x0000_0000 

0x3C 

Chip Select 0 Base Address 

0x0000_0009 

0x40 

Chip Select 1 Base Address 

0x0000_1081 

0x44 

Chip Select 2 Base Address 

0x0000_1181 

0x48 

Chip Select 3 Base Address 

0x0000_0000 

0x4C Interrupt 

Control/Status 0x0049 

0x4E 

EEPROM Write Protect Boundary 

0x0030 

0x50 Miscellaneous 

Control 

Register 0x0078_0000 

0x54 General 

Purpose 

I/O Control 

0x0224_9252 

0x70 

Hidden1 Power Management 

0x0000_0000 

0x74 

Hidden 2 Power Management 

0x0000_0000 

Table 4-2 :  PCI9030 Local Configuration Register

 

Summary of Contents for TPMC310























Reviews:

No comments

Brands by name

Popular brands

Load more brands