manualshive.com logo in svg

TestPad BTS-2002H, Manual

Share
Download
TestPad BTS-2002H Manual Download Page 22

Shenzhen TestPad Electronic Co., Ltd.

http://www.test-pad.com

22

RUN: Run mode

PAUSE: Pause mode

ERROR: Operation error

COMP: Operation completion

(Line 2)

RUN TIME: 00:03:17: It indicates the accumulated duration of the test.

V=8.42V: It indicates the voltage of the battery. If “+/-“ is displayed, it indicates that the

battery is connected reversely.

I=0.683A: It indicates the current of the battery.

If the battery is being charged, it indicates the charge current. If the battery is being

damaged, it indicates the discharge current.

In the charge mode, if “CHARGE CAP: 26mAH” is displayed, it indicates that the charged

capacity is 26mAH.

In the discharge mode, if “DISCHR CAP: 1234mAH” is displayed, it indicates that the

discharged capacity is 1234mAH.

If the test is completed and the over-charge test and over-discharge test are enabled, the

over-charge voltage, the over-discharge protection current, and the finally discharged

capacity will be displayed here in turn.

In case of a fault, the test is aborted, and the fault cause is displayed here.

Caution: If the capacity of Nickel-Metal hydride battery or Nickel-Cadmium battery need be

tested, our delivery-attached temperature sensor is recommended. Place the temperature sensor

close to the surface of the battery to be tested, and connect the temperature sensor to the P- and R2

of the tester, thus to ensure safe charge.

Summary of Contents for BTS-2002H




































Reviews:

No comments

Brands by name

Popular brands

Load more brands