manualshive.com logo in svg

TestPad BTS-2002H, Manual

Share
Download
TestPad BTS-2002H Manual Download Page 15

Shenzhen TestPad Electronic Co., Ltd.

http://www.test-pad.com

15

On the static parameter setup interface, there are 24 configurable items.

1.

Pack type: The options include:

a)

Lion: Li-ion battery

b)

NiMH: Nickel-Metal hydride battery

c)

NiCd: Nickel-Cadmium battery

d)

SLA: Maintenance-free lead-acid battery

2.

Pack Vol: The options include:

a)

For Li-ion battery, it may increase by 3.6V per additional battery, and the maximum value

is 14.4V (BTS-2004H).

b)

For Nickel-Metal hydride battery and Nickel-Cadmium battery, it may increase by 1.2V per

additional battery, and the maximum value is 14.4V (BTS-2004H).

c)

For the SLA battery, it may increase by 2V per additional battery, and the maximum value

is 12V (BTS-2004H).

3.

Pack Cap: Set the capacity of the battery. In the subsequent test, the tester will

automatically select the appropriate value for test according to the capacity set here. It may

increase by a step of 50mAH ~ 1000mAH per time, and the maximum value is 10000 mAH

(BTS-2004H).

4.

Charge: Enable or disable the test. Press LEFT or RIGHT to adjust the selection.

5.

Discharge: Enable or disable the test. Press LEFT or RIGHT to adjust the selection.

6.

Over Current: For Li-ion battery, enable or disable the test. For other battery types, this

function is unavailable.

7.

R1: Enable or disable the test. (Identification resistor 1)

8.

R2: Enable or disable the test. (Identification resistor 2)

9.

Vol-Min: It may increase or decrease by a step of 10 mV. When the battery type or battery

voltage is changed, this parameter will be restored to the minimum default value.

10. Vol-Max: It may increase or decrease by a step of 10mV. When the battery type or battery

voltage is changed, this parameter will be restored to the maximum default value.

11. IMP-Min: The maximum value is 0.mΩ.

12. IMP-Max: The maximum value is 999 mΩ. If it is set to be a value larger than 999 mΩ, the

impedance test is disabled.

13. OVC-Min: This parameter can be adjusted only when the over-current test is enabled. It

may increase or decrease at a step of 0.1A.

Summary of Contents for BTS-2002H




































Reviews:

No comments

Brands by name

Popular brands

Load more brands