Testomat 2000 THCL Operating Instructions Manual Download | Manualshive

Page: 12 / 51

background image

Installation

12

Connecting the power supply and devices

Risk of electric shocks during installation!

If the power supply is not disconnected prior to installation, it may
result in personal injuries, destruction of the product or damage to
plant parts.

Always disconnect the relevant plant parts before installing Tes-

tomat 2000

®

THCL.

Only use tested cables with sufficient cross-sections for the con-
nections.

Risk of damages caused by electromagnetic fields!

If Testomat 2000

®

THCL or the connecting cables are installed

parallel to power cables or in close proximity to electromagnetic
fields, the instrument may be damaged or measurements incor-
rect.

Ensure that connecting cables are as short as possible.

Always install connecting cables and power cables separately.

Connect the instrument to the protective earth conductor (for

230/115 VAC).

Protect Testomat 2000

®

THCL against interference voltages – e.g.

via a mains filter.

Shield the instrument against strong electromagnetic fields.

Block diagram Testomat 2000

®

THCL

Drawn relay positions: Instrument de-energised

WARNING

!

NOTE

«
...
10
11
12
13
14
...
»

Summary of Contents for 2000 THCL




















































Reviews:

No comments

Related manuals for 2000 THCL

Brand: Omicron Pages: 80

Brand: Hach Pages: 145

Brand: Hach Pages: 358

Polymetron 9582sc

Brand: Hach Pages: 280

Brand: HACH LANGE Pages: 15

Brand: Oakton Pages: 16

Brand: Parkside Pages: 94

Brand: +GF+ Pages: 8

Brand: Trebs Pages: 44

Greenlee CLM-1000

Brand: Textron Pages: 36

Brand: FMS Pages: 12

Brand: Dynojet Pages: 88

Brand: VP instruments Pages: 15

Brand: 3M Pages: 168

Brand: ACCRETECH Pages: 104

Brand: General Pages: 12

Brand: YOKOGAWA Pages: 104

Brand: Reed Instruments Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands