background image

 
Vibrating Table 
2.0231 / 2.0268 / 2.0269 
2.0131 / 2.0233 / 2.0234 
2.0271 

 

17 

  By pressing the START-STOP button, you can show the value of the respective pa-

rameter. If you then at the same time also press the upward button (

) or the down-

ward button (

) while still holding down the START-STOP button, you can change the 

value of the parameter being shown. 

  When you release all the buttons, this will permanently save the new value. If you press 

no button for longer than 60 seconds,  or if you press BOTH the upward button (

AND the downward button (

) at the same time for at least four (4) seconds, the sys-

tem will jump back to the original state. 

 

Parameters: 

Functional description 

Setting range 

Default 

Customer’s set-
ting 

P1 

Time range 

0:  0 … 999 s 
1:  0 … 999 min 
2:  0 … 999 h 
3:  0 … 999 tenths of 
seconds 

P5 

Function of input E1 
(START/STOP) 

0:  effective when 
closing 
1:  effective when 
opening 

P7 

Function of output K1 

0:  active ON 
1:  active OFF 

P9 

Signal duration of buzzer 

0 … 10 s 

10 

P10 

Trip for start function 

0:  button or input 
1:  only button 
2:  only input 

P11 

Trip for stop function 

0:  button or input 
1:  only button 
2:  only input 

P12 

Display of actual time 

0:  remaining time 
1:  time elapsed 

P17 

Auto reset 

0:  no auto reset 
1:  timer has run out: 
reset 

 

5.3  Setting the time for the timer to run 

 

  Connect the Vibrating Table with Timer Switch to the power source. 

  You now set the time for the timer switch to run by briefly pressing the upward 

button (

) or the downward button (

). 

  You can now start the timer switch by pressing the START-STOP button. 

 
 
 
 
 
 
 
 
 
 
 

 

Upward 

button 

Downward button 

START-STOP button 

Summary of Contents for 2 0131























Reviews: