Terra Universal USP 797 Quick Start Operating Manual Download Page 9

Page: 9 / 42

Quick-Start Operating Guide

USP 797 Modular Cleanroom

Terra Universal, Inc. • TerraUniversal.com • 800 S. Raymond Ave. • Fullerton, CA 92831 • TEL: (714) 578-6000 • FAX: (714) 578-6020

Component List (included)

This list includes the basic cleanroom components and may not be complete. Quantities vary based on the

specifications of each particular unit:

NOTE:

Refer to “Hardware Sheet” and “Crate Pages” included with your delivery for complete information specific to

your order.

Room structure:

Upright Frame Supports

Horizontal Frame Members

Long and Short Ceiling “T” Joists numbered to facilitate installation (see system drawings)

SS Window Frames (interior and exterior)

0.25” thick x 46”W x 36”H tempered glass window

Polypropylene Air Exhaust Vents

2’ x 4’ Polypropylene Ceiling Panels

FRP Side Panels (Fiberglass Reinforced Plastic): (12) 4’ x 8’ sheets (includes one extra)

Advanced Polymer FRP Adhesive

Sealant for FRP Seams

Powder-coated Steel Trim Strips (top horizontal)

Operation Status Indicators (4), installed in top trim corner pieces

U-brackets (provide mounting support for dry wall installation)

.25” and .125” plastic spacers (for mounting FRP panels)

Outlet template (guide for FRP cut-out to accommodate duplex outlet)

Yellow warning stickers, instructing personnel not to stand or walk on cleanroom ceiling

Hardware:

See list on following two pages

Tubing/Cords:

Polyethylene tubing

Yellow cord (with 3- and 4 pin-connections) to connect blowers and lights

Mini Yellow cord (with 4- and 5-pin connections) to connect control panel and Power Distribution Module (PDM)

White telephone cable for Status Indicator Lights

Warning Labels to attach to Ceiling Trim

Electrical:

Electrical Service Equipment, including

One (1) master light toggle switch, mounted on control panel

One (1) master blower switch (ON/OFF pushbuttons), mounted on control panel

Power Distribution Module (controls up to 5 lights and 4 Fan Filter Units)

115 or 230 VAC yellow power cables (for connection to FFUs and lights).

Duplex Power Outlet, installed on upright frame support in Buffer Room

Operation Status Indicators: mounted on each exterior corner

Summary of Contents for USP 797











































Search results

Summary of Contents for USP 797

Reviews:

Related manuals for USP 797

Brands by name

Popular brands

Terra Universal USP 797, Quick Start Operating Manual

Search results

Summary of Contents for USP 797

Reviews:

Related manuals for USP 797

Brands by name

Popular brands