manualshive.com logo in svg

Terra Universal USP 797, Quick Start Operating Manual

Share
Download
Terra Universal USP 797 Quick Start Operating Manual Download Page 36

Quick-Start Operating Guide 

 

 

USP 797 Modular Cleanroom 

© 

Copyright 2015 Terra Universal Inc.  All rights reserved.  • Revised Dec 2019  •  Document No. 1800-90  

Terra Universal, Inc.  •  TerraUniversal.com  •  800 S. Raymond Ave.  •  Fullerton, CA  92831  •  TEL: (714) 578-6000  •  FAX: (714) 578-6020 

36 

 

 

 

Removal and Replacement of the HEPA/ULPA Filter (Standard Unit) 

 

 

Warning: Disconnect the unit from the electrical power source before attempting any service. 

  

Warning: The Standard Filter is protected with an expanded metal face screen. This is never to be 

used to handle the filter. It is only for protection against an accidental touch of the filter. Handle filter only by 

the frame.  

 

Tools Required: Phillips Head Driver 

 

Step 1: 

Disconnect yellow power cable and remove unit from ceiling (see next page for recommended procedure). 

 

Step 2: 

Remove the 10 screws holding the HEPA/ULPA filter to the lid assembly.  

 

Step 3: 

Lift the lid assembly off the HEPA/ULPA filter (see figure below). Discard the used filter as per applicable 

regulations. 

 

Note:

 Before replacing with a new HEPA/ULPA filter, carefully inspect the new filter for any visible damage.  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Instructions for removing the Fan Filter Unit from the cleanroom ceiling grid 

Summary of Contents for USP 797











































Reviews:

No comments

Brands by name

Popular brands

Load more brands