TEREXLIFT Agrilift 625 Operator'S Handbook Manual Download Page 82

Page: 82 / 146

Page

D-8

MAINTENANCE

Document 57.0003.4200 - 03/2005

Handler with telescopic boom

Agrilift 625 - Telelift 2506

■

D-3.4

TYRES AND WHEELS

DANGER

Over-inflated or overheated tyres can burst. Do not
flame-cut or weld the wheel rims. For any repair
work, call in a qualified technician.

On new machines, and when a wheel has been
disassembled or replaced, check the nut torque of the
wheels every 2 hours until they stay correct.

ATTENTION

Always use tyres having the dimensions indicated
in the vehicle registration card.

For the tyre inflation or substitution, please refer to the
table below:

SERVICE INTERVAL

Running-in _________

Within the first

hours

Ordinary __________________

Every

250

hours

AGRILIFT 625

TELELIFT 2506

Dimensions

12-16.5

Load index

pr 10

Rim

9.75x16

Wheel disc

8 holes DIN 70361

Pressure

bar

4.5

Psi

RIGHT WAY

WRONG WAY

YES

Courtesy of Crane.Market

Summary of Contents for Agrilift 625



















































































































































Search results

Summary of Contents for Agrilift 625

Reviews:

TEREXLIFT Agrilift 625, Operator'S Handbook Manual, Page: 82 / 146

Search results

Summary of Contents for Agrilift 625

Reviews: