manualshive.com logo in svg

TEREXLIFT Agrilift 625, Operator'S Handbook Manual, Page: 79 / 146

Share
Download
TEREXLIFT Agrilift 625 Operator'S Handbook Manual Download Page 79

Page

  

D-5

MAINTENANCE

Document 57.0003.4200 - 03/2005

Handler with telescopic boom 

 Agrilift 625 - Telelift 2506

 D-3  MAINTENANCE JOBS

DANGER

All maintenance interventions must be carried out
with engine stopped, parking brake engaged,
working attachments flat on the ground and gear
lever in neutral.

CAUTION

When raising a component for maintenance
purposes, secure it in a safe way before any
maintenance intervention.

CAUTION

Any intervention on the hydraulic circuit must be
carried out by skilled personnel.
The hydraulic circuit of this machine is fitted with
pressure accumulators. You and others could be
seriously injured if accumulators are not completely
depressurised.
To  depressurise the accumators, just steer the
machine wheels some times with engine shut down
until noticing a gradual binding of the handwheel.

CAUTION

Before any operation on hydraulic lines or
components, make sure there is no residual
pressure. For this purpose, stop the engine, engage
the parking brake and operate the control levers of
the distributors in both working directions
(alternately) to depressurise the hydraulic circuit.

ATTENTION

High pressure lines must be replaced by qualified
personnel only.
Any foreign matters entering the closed circuit may
result in a sudden deterioration of the transmission.

ATTENTION

The qualified staff charged with the maintenance
of the hydraulic circuit must clean all areas around
with care before any intervention.

PROTECT THE

ENVIRONMENT

The handling and disposing of used oils can be
ruled by local or national regulations. Address to
authorised centres.

■

  D-3.1

DISCONNECTING THE BATTERY

During maintenance or repair works, and while welding,
turn off the battery main switch, located behind the
rear right wheel compartment (

C-4.5, p. C-25

).

Courtesy of Crane.Market 

Summary of Contents for Agrilift 625



















































































































































Reviews:

No comments