TEREXLIFT Agrilift 625 Operator'S Handbook Manual Download Page 49 | Manualshive

Page: 49 / 146

TEREXLIFT Agrilift 625 Operator'S Handbook Manual Download Page 49

Page

C-13

OPERATING INSTRUCTIONS

Document 57.0003.4200 - 03/2005

Handler with telescopic boom

Agrilift 625 - Telelift 2506

■

C-3.2.9

Auxiliary drive controls

Beacon

When the machine is started up, the beacon
activates automatically.

22

Optional attachment pushbutton (if any)

Pushbutton with orange glass.
The pressure of this button causes the
switching of the hydraulic circuit for the
movement of the attachments equipped with
auxiliary lines.

10

Hazard warning lights switch

Fitted with on-off position, it switches on the
turn signals simultaneously

12

Road lights switch

This switch is located above the ignition
switch and is used in conjunction with lever

5

(

see C-3.2.3

).

23

Air conditioning fan switch

Three-position switch:

0

OFF

1

Low speed

2

High speed

21

Cab heater control cock

To the right of the driving seat.
• Rotate clockwise for fresh air
• Rotate anticlockwise for warm air
• Adjust the flow of warm air within the cab by

the air conditioning fan switch

23

.

40

80

120

°

C

0 1 2 3 4 5 6 7

80

120

°

C

40

F

R

N

10

12

5

C

A

22

21

23

Courtesy of Crane.Market

«
...
47
48
49
50
51
...
»

Summary of Contents for Agrilift 625



















































































































































Reviews:

No comments