manualshive.com logo in svg

TEREXLIFT Agrilift 625, Operator'S Handbook Manual, Page: 117 / 146

Share
Download
TEREXLIFT Agrilift 625 Operator'S Handbook Manual Download Page 117

Page

  

G-1

TABLES AND DOCUMENTS ENCLOSED

Document 57.0003.4200 - 05/2007

Handler with telescopic boom 

 Agrilift 625 - Telelift 2506

G-1

TORQUE WRENCH SETTING ...............................................................

G-2

G-2.1

Load Chart with forks ............................................................................

G-3

G-2.2

Load Chart with forks ............................................................................

G-4

G-3.1

Wiring diagram - Fuses and relays ........................................................

G-5

G-3.2.1

Wiring diagram (valid up to serial no. 17083) ........................................

G-7

G-3.2.2

Wiring diagram (valid from serial no. 17084) .........................................

G-17

G-3.3

General wiring diagram (description) ....................................................

G-27

G-4.1

Hydraulic scheme ..................................................................................

G-29

G-5

Routine check schedule-Safety devices ...............................................

G-30

Section

 

G

TABLES AND

DOCUMENTS ENCLOSED

TABLE OF CONTENTS

Courtesy of Crane.Market 

Summary of Contents for Agrilift 625



















































































































































Reviews:

No comments