Tequipment FLUKE i1010, Service Information

Page: 5 / 9

Service Information
Preparing for Calibration
5
Table 4. Performance Test Values
Step Calibrator
Setting 50T Coil
Current Measure i410
Lo mV i410
Hi mV i1010
Lo mV i1010
Hi mV
DC Amps Zero Test
1 0.0
(ZERO knob CW)
NA Pos. span 3.0 15.0 3.0 15.0
2 0.0
(ZERO knob CCW)
NA Neg. span
−
15.0
−
3.0
−
15.0
−
3.0
DC Amps Test
1
3 0.04A dc 2.0A dc 2.00 mV 1.43 2.57 1.46 2.54
4 0.4A dc 20.0A dc 20.0 mV 18.8 21.2 19.1 20.9
5 -0.4A dc -20.0A dc -20.0 mV -21.2 -18.8 -20.9 -19.1
6 1.2A dc 60.0A dc 60.0 mV 57.4 62.6 58.3 61.7
AC Amps Test
7 0.40A, 45 Hz, 400 Hz 20.0A ac 20.0 mV 18.8 21.2 19.1 20.9
8 0.40A, 2 kHz 20.0A ac 20.0 mV NA NA 18.9 21.1
9 1.0A 45 Hz, 400 Hz 50.0A ac 50.0 mV 47.7 52.3 48.5 51.5
10 1.0A 2 kHz 50.0A ac 50.0 mV NA NA 48.0 52.0
11 2.0A, 45 Hz, 400 Hz 100.0A ac 100.0 mV 96.0 104.0 97.5 102.5
12 2.0A, 1 kHz 100.0A ac 100.0 mV NA NA 96.5 103.5
DC Amps Balance Test
13 4.0A dc 200.0A dc 200.0 mV
1.0A maximum change from Center of Jaw
Reading to Top or Bottom of Jaw Readings.
DC Amps Test
14 4.0A dc 200.0A dc 200.0 mV 192.5 207.5 195.5 204.5
15 8.0A dc 400.0A dc 0.4000V 0.3855V 0.4145V 0.3915V 0.4085V
16 -8.0A dc -400.0A dc -0.4000V -0.4145V -0.3855V NA NA
17 -12.0A dc -600.0A dc -0.6000V NA NA -0.6125V -0.5875V
18 20.0A dc 1000.0A dc 1.0000V NA NA 0.9795V 1.0205V
19 -20.0A dc -1000.0A dc -1.0000V NA NA -1.0205V -0.9795V
AC Amps Test
20 2.4A, 45 Hz, 400 Hz 120.0A ac 120.0 mV 115.3 124.7 117.1 122.9
21 2.4A, 800 Hz 120.0A ac 120.0 mV NA NA 115.9 124.1
22 5.0A, 45 Hz, 400 Hz 250.0A ac 250.0 mV 240.7 259.3 244.5 255.5
23 8.0A, 45 Hz, 400 Hz 400.0A ac 0.4000V 0.3855V 0.4145V NA NA
24 12.0A, 45 Hz, 65 Hz 600.0A ac 0.6000V NA NA 0.5875V 0.6125V
Notes:
1. Prior to performing DC Amp tests, adjust ZERO so that the DMM reads 00.0 +/- 00.1 mV without current applied.