Tennant 365 Operator'S Manual Download Page 8

Page: 8 / 102

GENERAL INFORMATION

365 MM173 (3---90)

WARNING: Fuel vapor is present when

servicing fuel system. Fire or explosion can

result. Keep flames and sparks away.

WARNING: Machine moves when

directional pedal linkage is out of

adjustment. Severe personal injury or death can

result. If machine creeps when the directional

pedal is in neutral, adjust pedal linkage. Engage

parking brake when stopped.

WARNING: Machine is unstable on jack.

Jack machine up at designated locations

only. Block machine up with jack stands.

WARNING: Machine is unstable on jack.

Block machine tires before jacking machine

up.

WARNING: Leaking hydraulic fluid under

pressure can penetrate skin. Severe

infection or death can result. Do not use body to

locate leak. Use cardboard to locate leak.

WARNING: Hot engine coolant. Scalding

can result. Do not open radiator cap or

service cooling system until radiator and engine

is cool to the touch.

WARNING: Air or water under pressure.

Severe eye or ear injury can result. Wear

eye and ear protection.

WARNING: LPG fuel is very cold. Frostbite

can result. Wear gloves when connecting or

disconnecting LPG hoses.

WARNING: Stay clear of hopper lift arms

when they are in motion.

Summary of Contents for 365







































































































Search results

Summary of Contents for 365

Reviews:

Tennant 365, Operator'S Manual, Page: 8 / 102

Search results

Summary of Contents for 365

Reviews: