Tennant 365 Operator'S Manual Download Page 57

Page: 57 / 102

MAINTENANCE

3-15

365 MM173 (3---90)

HYDRAULIC SYSTEM TROUBLESHOOTING

Problem

Cause

Remedy

Bad coil at S2.

Replace coil.

Bad seal at S2.

Replace seal.

Bad electrical connection

Remake connection.

at S2.
Circuit breaker tripped CB-5.

Reset circuit breaker CB-5.

Look for short circuit.

Bad electrical relay M4.

Replace electrical relay M4.

Hopper lift micro-switch

Check connection at

not operating.

micro-switch. Check adjustment of

hopper and fan inlet bracket.

Main brush micro-switch

Check connections at

not operating.

micro-switch on main brush handle.

Bad relief valve at R1.

Replace relief cartridge R1.

Bad coil at S3.

Replace coil.

Cartridge stuck open at S3.

Replace cartridge.

Bad electrical connection

Remake connection.

at S3.
Two-speed rocker switch not

Replace rocker switch or

working.

check electrical connections.

Circuit breaker tripped CB-5.

Reset circuit breaker CB-5.

Look for short circuit.

Bad coil at S4.

Replace coil.

Cartridge stuck open at S4.

Replace cartridge.

Bad seal at S4.

Replace seal.

Bad electrical connection

Remake connection

at S4.
Hopper lift micro-switch

Check connection of

not operating.

micro-switch at hopper.

Thermo-Sentry

indicator

Reset Thermo-Sentry

switch

tripped

or replace it.

Vacuum fan rocker switch

Replace rocker switch or

not operating.

check electrical connections.

Relief valve R1 is stuck

Replace valve R1

open.
Circuit breaker tripped CB-5.

Reset circuit breaker CB-5.

Main brush does not turn.

Everything else works fine.

Vacuum fan does not turn.

Everything else works fine.

Two speed function of

main brush and vacuum

fan does not work. Operates

at slow speed only.

Main brush and vacuum fan

does not turn. Hopper does

not lift.

Summary of Contents for 365







































































































Search results

Summary of Contents for 365

Reviews:

Brands by name

Popular brands

Tennant 365, Operator'S Manual

Search results

Summary of Contents for 365

Reviews:

Brands by name

Popular brands