Tennant 365 Operator'S Manual Download Page 23

Page: 23 / 102

OPERATION

2-3

365 MM173 (3---90)

PREPARATION FOR OPERATION

AFTER UNLOADING AND BEFORE OPERATING

THE MACHINE:

1. Check the machine for shipping damage.

2. Read this manual carefully before operating or

servicing the machine.

FOR SAFETY: Do not operate the machine unless

operation manual is read and understood.

3. Check the hydraulic fluid level in the hydraulic

fluid reservoir, using the dipstick provided.

TENNANT hydraulic fluid is recommended. If

TENNANT hydraulic fluid is not available, use

only new, approved hydraulic fluid. See

HYDRAULICS

in the

MAINTENANCE

section.

4. Check the engine oil level.

5. Check the radiator coolant level.

6. Check the brush adjustment, as described in

BRUSHES

in the

MAINTENANCE

section.

7. Check the air pressure of the tires. Pressure

should be as listed in

BRAKES AND TIRES

the

MAINTENANCE

Section.

8. Fill the fuel tank, or install an LPG fuel tank on

the machine per the instructions in this manual.

WARNING: Machine can have static

electricity charge. When pouring fuel, spark

can ignite fuel causing fire or explosion. Connect

wire attached to fuel can to machine to discharge

spark before pouring fuel.

Summary of Contents for 365







































































































Search results

Summary of Contents for 365

Reviews:

Brands by name

Popular brands

Tennant 365, Operator'S Manual

Search results

Summary of Contents for 365

Reviews:

Brands by name

Popular brands