background image

TEMPUR-Ergo

 Plus

RADIO FREQUENCY IS 433 MHZ.

FCC COMPLIANCE

THIS device complies with part 15 of the FCC 
Rules. Operation is subject to the following 
two conditions: (1) This device may not cause 
harmful interference, and (2) this device must 
accept any interference received, including 
interference that may cause undesired 
operation.

TO comply with the FCC RF exposure 
compliance requirements, no change to the 
antenna or the device is permitted. Any change 
to the antenna or the device could result in the 
device exceeding the RF exposure requirements 
and void user’s authority to operate the device.

PRODUCT RATINGS

The lift motors in your TEMPUR-Ergo

 Plus are 

NOT

 

designed for continuous use. Reliable operation and 
full life expectancy will be attained as long as the lift 
motors do not operate more than two (2) minutes 
over an 20-minute period, or approximately 10% 
duty cycle. Any attempt to circumvent or exceed this 
rating will shorten the life expectancy of this product 
and may void the warranty. The recommended weight 
restrictions on our TEMPUR-Ergo Plus systems are 
as follows: Twin, Twin Long, Double, Queen, and 
Split/Dual CA King bases – up to 650 lbs. each. 
This TEMPUR-Ergo Plus will structurally support the 
recommended weight distributed evenly across the 
head and foot sections. This product is not designed to 
support or lift this amount of weight in the head or foot 
sections alone. 

NOTE: Exceeding the recommended weight 
restrictions could damage your TEMPUR-Ergo 
Plus and void your warranty. 

For best performance, you should enter and exit the 
TEMPUR-Ergo Plus while it is in the flat or fully lowered 
position.

INTENDED USAGE

The electric adjustable bed should be installed with 
the Headboard Bracket and/or the head of the frame 
should be positioned close to a wall.

8

CUSTOMER SERVICE: 1–800–821–6621

Summary of Contents for TEMPUR-ERGO PLUS

























Reviews: