Tema Telecomunicazioni AA-539 Technical Manual And Installation Manual Download Page 50 | Manualshive

Page: 50 / 57

background image

TEMA TELECOMUNICAZIONI SRL

Doorphone AA-539

MAS-AA539-REV02EN

Page 50 of 57

Additional parameters available regarding the direct selection of contact numbers. When this table is compiled
allows to activate the security function of some company internal extension or to make selectable only those listed
here (up to a maximum of 10 numbers).

230 #

Operation mode of
the filter table of the
visitor dialing

(the following table)

(fields from

231 to 240)

The value of this field set the following table to be considered
by the system as:

- a dialing accepting table
(numbers  or  parts  of  them  that  can  be  achieved  must  be
present  in  the  table,  all  others  are  considered  to  be  NOT
accessible)

- a dialing denial table
(numbers or parts of them that can NOT be achieved must be
present  in  the  table,  all  others  are  considered  to  be
accessible)

0 = operation as a an accepting table
1 = operation as a denial table

Range: max 1 character, values 0-1

1

231 #

Telephone number
(or prefix) 1

Number  to  be  considered  reachable  or  unreachable
depending  on  the  configuration  of  the  parameter  230.  This
feature  allows  to  the  system  equipped  with  complete
keyboard  expansion  to  consider  the  dialing  of  certain
numbers as valid or not and then allow or ignore the dialing.

Note:  The  entered  digits  can  also  be  considered  as  a  prefix,
to  enable  /  disable  all  the  numbers  that  begin  with  a  certain
sequence and must end with the same character * (star). For
example,  entering  1  in  the  parameter  230  and  9*  in  the
parameter 231, all the selections starting with 9 digit number
will not be considered by the system.

Range: max 5 characters, values 0-9 *

--

232 #

Tel. Numb. / Pref. 2

Same as above

--

233 #

Tel. Numb. / Pref. 3

Same as above

--

234 #

Tel. Numb. / Pref. 4

Same as above

--

235 #

Tel. Numb. / Pref. 5

Same as above

--

236 #

Tel. Numb. / Pref. 6

Same as above

--

237 #

Tel. Numb. / Pref. 7

Same as above

--

238 #

Tel. Numb. / Pref. 8

Same as above

--

239 #

Tel. Numb. / Pref. 9

Same as above

--

240 #

Tel. Numb. / Pref. 10

Same as above

--

9.6.

Special commands

Special commands active during the programming steps

0#

End of
programming

Finish the current programming.

300#

Firmware version
of the device

Plays 2 series of tones indicating the installed firmware version.

Special commands active before the programming stage, after calling the system and have
entered only the *** (3 times star) code, to request entry into programming, but without
having entered the correct password.

**##**

Back to default

Back to factory default all the system parameters
(two stars, two pounds, two stars).

9.7.

Examples of programming / Operator commands

«
...
48
49
50
51
52
...
»

Summary of Contents for AA-539


























































Reviews:

No comments

Related manuals for AA-539

Brand: Jensen Pages: 2

Brand: Jensen Pages: 16

Brand: FARFISA INTERCOMS Pages: 16

Brand: QSC Pages: 4

Brand: Parkside Pages: 124

Brand: JBL Pages: 4

Brand: JBL Pages: 157

Brand: BAS-IP Pages: 16

Brand: Gage Pages: 36

4.3" Video Door Phone

Brand: Alarmtec Pages: 14

Brand: Ibiza sound Pages: 50

Brand: Real-El Pages: 6

R7F4DC-DAC16D-H

Brand: M-system Pages: 8

MR Confon Starter f MKII+

Brand: Cambridge Research Systems Pages: 34

Brand: Measurement Computing Pages: 50

eBOX550-100-FL Series

Brand: AXIOMTEK Pages: 78

Brand: Slinex Pages: 8

Headzone PRO XT

Brand: Beyerdynamic Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands