Tema Telecomunicazioni AA-539 Technical Manual And Installation Manual Download Page 1 | Manualshive

Page: 1 / 57

background image

Revision

Date

Revision reason

Prepared

Checked/Approved

2

13-09-2016 Update

GM, GBC

FL

MAS-AA539-REV02EN

Page 1 of 57

AA-539

Vandal-proof Analog Doorphone with 1 button

for connection to PBX extension (FXO)

AA-539K additional keyboard module

AA-539R additional index module

TECHNICAL MANUAL – INSTALLATION

PRELIMINARY DOCUMENTATION

AA-539 system manual - Version HW 2.0 – FW 1.8

Recommendations

1.

Use only original spare parts and consumables supplied by Tema Telecomunicazioni Srl for this equipment. The company shall not be
held responsible for any damage caused by the use of materials that they have not supplied.

2.

The device has been carefully manufactured and tested. In any case, the product is not recommended for use in situations in which
incorrect operating may result in damage to persons and/or property.

3.

We recommend that you carefully read all this manual before starting to use the device.

4.

Do not expose the device to sunlight and protect it from sources of heat, dust, humidity and chemical agents.

5.

This manual is the property of Tema Telecomunicazioni Srl and any duplication and reproduction, even partial, as well as storage on
any type of media is forbidden without written permission from Tema Telecomunicazioni Srl.

TEMA TELECOMUNICAZIONI S.r.l.

Telecommunications - Electronics

1
2
3
...
»

Summary of Contents for AA-539


























































Reviews:

No comments

Related manuals for AA-539

Brand: Oklahoma Sound Pages: 4

Brand: Jensen Pages: 12

Brand: ASL INTERCOM Pages: 11

Brand: QTS Pages: 50

Brand: WAGO Pages: 20

ActivSoundBar TP-1866-UK

Brand: promethean Pages: 28

Brand: Legacy Pages: 21

Brand: Acces Pages: 17

Brand: Talk-a-Phone Pages: 13

Brand: iLive Pages: 12

Brand: DAPAudio Pages: 13

Powerbox PA 802

Brand: Conrad Pages: 4

YDDSEL0H301-2-BK

Brand: CEBIHEP Pages: 4

Brand: H&B Pages: 9

Brand: Polk Audio Pages: 10

Brand: Fuslon Pages: 14

Brand: RTS Pages: 14

Inspire SBS Vivid 60

Brand: Creative Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands