Teltonika FMA120 User Manual Download Page 4

Page: 4 / 106

8.4.12

SMS Data send week time schedule (ID=1273) ...................................................... 66

8.4.13

Authorized phone numbers (ID=1260-1270) .......................................................... 66

8.4.14

SMS Event PreDefined Numbers (ID=150-159) ....................................................... 66

8.4.15

Operator List (ID=1271 X) ....................................................................................... 66

8.4.16

Black Operator list (ID= 1272 X) ............................................................................. 67

8.5

ATA

CQUISITION

ODES PARAMETERS

.................................................................................. 67

8.5.1

Home Network GSM operator code “Vehicle on STOP” parameters

...................... 67

8.5.1.1

Min Period (ID=1540)

......................................................................................................... 67

8.5.1.2

Min Saved Records (ID=1543)

............................................................................................. 67

8.5.1.3

Send Period (ID=1544)

........................................................................................................ 67

8.5.1.4

GPRS Week Time (ID=1545)

................................................................................................ 67

8.5.2

Home Network GSM operator code “Vehicle MOVING” parameters

..................... 68

8.5.2.1

Min Period (ID=1550)

......................................................................................................... 68

8.5.2.2

Min Distance (ID=1551)

...................................................................................................... 68

8.5.2.3

Min Angle (ID=1552)

.......................................................................................................... 68

8.5.2.4

Min Saved Records (ID=1553)

............................................................................................. 69

8.5.2.5

Send Period (ID=1554) ....................................................................................................... 69

8.5.2.6

GPRS Week Time (ID=1555)

................................................................................................ 69

8.5.2.7

Min Speed (ID=1556)

.......................................................................................................... 69

8.5.2.8

Min Speed Source (ID=1557)

.............................................................................................. 69

8.5.3

Roaming Network GSM operator code “Vehicle on STOP” parameters

................. 69

8.5.3.1

Min Period (ID=1560)

......................................................................................................... 69

8.5.3.2

Min Saved Records (ID=1563)

............................................................................................. 70

8.5.3.3

Send Period (ID=1564)

........................................................................................................ 70

8.5.3.4

GPRS Week Time (ID=1565)

................................................................................................ 70

8.5.4

Roaming Network GSM operator code “Vehicle MOVING” parameters

................ 70

8.5.4.1

Min Period (ID=1570)

......................................................................................................... 70

8.5.4.2

Min Distance (ID=1571)

...................................................................................................... 70

8.5.4.3

Min Angle (ID=1572)

.......................................................................................................... 70

8.5.4.4

Min Saved Records (ID=1573)

............................................................................................. 71

8.5.4.5

Send Period (ID=1574)

........................................................................................................ 71

8.5.4.6

GPRS Week Time (ID=1575)

................................................................................................ 71

8.5.4.7

Min Speed (ID=1576)

.......................................................................................................... 71

8.5.4.8

Min Speed Source (ID=1577)

.............................................................................................. 71

8.5.5

Unknown Network GSM operator code “Vehicle on STOP” parameters

................ 72

8.5.5.1

Min Period (ID=1580)

......................................................................................................... 72

8.5.5.2

Min Saved Records (ID=1583)

............................................................................................. 72

8.5.5.3

Send Period (ID=1584)

........................................................................................................ 72

8.5.5.4

GPRS Week Time (ID=1585)

................................................................................................ 72

8.5.6

Unknown Network GSM operator code “Vehicle MOVING” parameters

............... 72

8.5.6.1

Min Period (ID=1590)

......................................................................................................... 72

8.5.6.2

Min Distance (ID=1591)

...................................................................................................... 72

8.5.6.3

Min Angle (ID=1592)

.......................................................................................................... 73

8.5.6.4

Min Saved Records (ID=1593)

............................................................................................. 73

8.5.6.5

Send Period (ID=1594)

........................................................................................................ 73

8.5.6.6

GPRS Week Time (ID=1595)

................................................................................................ 73

Read chapter 8.5.1.4.

.......................................................................................................................... 73

8.5.6.7

Min Speed (ID=1596)

.......................................................................................................... 73

8.5.6.8

Min Speed Source (ID=1597)

.............................................................................................. 74

8.6

EATURES

ARAMETERS

......................................................................................................... 74

8.6.1

Green driving scenario (ID=1890) ........................................................................... 74

8.6.2

Green Driving digital output control (ID=1891) ...................................................... 74

8.6.3

Max Acceleration Force (ID=1892) ......................................................................... 74

8.6.4

Max Braking Force (ID=1893) ................................................................................. 74

8.6.5

Max Cornering Force (ID=1894) ............................................................................. 74

8.6.6

Overspeeding scenario (ID=1895) ........................................................................... 75

8.6.7

Over Speeding digital output control (ID=1896) ..................................................... 75

8.6.8

Max allowed speed (ID=1897) ................................................................................ 75

8.6.9

Jamming scenario (ID=1898) .................................................................................. 75

8.6.10

Jamming digital output control (ID=1899) ............................................................. 75

8.6.11

Jamming sensitivity (ID=1900) ................................................................................ 75

Summary of Contents for FMA120











































































































Search results

Summary of Contents for FMA120

Reviews:

Related manuals for FMA120

Brands by name

Popular brands

Teltonika FMA120, User Manual

Search results

Summary of Contents for FMA120

Reviews:

Related manuals for FMA120

Brands by name

Popular brands