Teltonika FM1120 User Manual Download Page 60

 

 

 

 

 

60 

 

 

8.4

 

GSM parameters 

8.4.1

 

GPRS content ac

t

ivation (ID=1240) 

Parameter allows or does not allow GPRS usage. If GPRS is not allowed value is 0, if GPRS is 

allowed value is 1. 

Minimum 

value 

Maximum 

value 

Recommended 

value 

Goes with (depends on) 

parameters 

Value 

type 

APN

 Name (ID=1242)

 

APN username (ID=1243)

 

APN Password (ID=1244)

 

S8 

8.4.2

 

APN Name (ID=1242) 

Parameter defines GPRS Access Point Name.  

Minimum 

value 

Maximum 

value 

Recommended 

value 

Goes with (depends on) 

parameters 

Value 

type 

Empty 

32 char 

string 

GPRS content activation (ID=1240) 

APN username (ID=1243)

 

APN Password (ID=1244)

 

S8[32] 

8.4.3

 

APN username (ID=1243) 

Parameter  defines  APN  username.  In  case  operator  does  not  use  username  for  login, 

value should be empty.  

Minimum 

value 

Maximum 

value 

Recommended 

value 

Goes with (depends on) 

parameters 

Value 

type 

Empty 

30 char 

string 

GPRS content activation (ID=1240) 

APN

 Name (ID=1242)

 

APN Password (ID=1244)

 

S8[30] 

8.4.4

 

APN Password (ID=1244) 

Parameter defines APN password. In case operator does not use password for login, value 

should be empty. 

Minimum 

value 

Maximum 

value 

Recommended 

value 

Goes with (depends on) 

parameters 

Value 

type 

Empty 

30 char 

string 

GPRS content activation (ID=1240) 

APN

 Name (ID=1242)

 

APN username (ID=1243)

 

S8[30] 

8.4.5

 

Domain (ID=1245) 

Parameter defines AVL data destination server IP address. Example: 212.47.99.62 

Minimum 

value 

Maximum 

value 

Recommended 

value 

Goes with (depends on) 

parameters 

Value 

type 

31 char 

string 

GPRS content activation (ID=1240) 

Domain

 (ID=1245)

 

S8[16] 

8.4.6

 

Target Server Port (ID=1246) 

Parameter defines AVL data destination server port number. Example: 12050 

Summary of Contents for FM1120

























































































Reviews: