Telonics MINI-12 User Manual Download Page 36 | Manualshive

Page: 36 / 62

background image

Telonics TCA-500C Combo Amp

36

PB-009289 Rev E

TCA-500C

C

OMBO

A

MP

S

ETUP

S

ETTINGS

:

(

CONTINUED

)

M

ORE

A

GGRESSIVE

S

ETTING

These EQ settings, with only slight variations, are used by a number of professional musicians to
“cut through the mix” in live band applications.
Sonically, it is designed to “fit” in the “pocket” above the bass and low keyboards and below the
strings, providing clarity to the steel without clashing against the other orchestral elements. As
such, it may appear brash, or too “out in front” when playing with little or no accompaniment.
However in live applications, when used with the proper pickups, cables and volume pedal, it
can sit well in the mix and provide a live sound reminiscent of Push-Pull guitars at their best. It is
generally fine-tuned by moving the BLEND control plus or minus one mark on the dial either
way.

Once the equalization is set to your satisfaction, the BLEND control can be rocked slowly while
striking a wide grip of strings repeatedly to accurately “fine tune” all the EQ settings at one time.

Remember that these controls are sensitive, so a little adjustment can change a lot.

A

NOTHER

F

AVORITE

S

ETTING FOR SOME

P

ROFESSIONAL

P

LAYERS

These settings are favored by a number of leading musicians. While projecting well in solo
performances, they provide an extremely full bodied sound with bell-like clarity and superb
string separation with most pickups.

Once the equalization is set to your satisfaction, the BLEND control can be rocked slowly while
striking a wide grip of strings repeatedly to accurately “fine tune” all the EQ settings at one time.

Remember that these controls are sensitive, so a little adjustment can change a lot.

«
...
34
35
36
37
38
...
»

Summary of Contents for MINI-12































































Reviews:

No comments

Related manuals for MINI-12

Brand: LABTEC Pages: 12

Brand: JBL Pages: 8

Brand: CableTronix Pages: 3

N-10 Honeytone Mini Amp

Brand: Danelectro Pages: 2

Brand: Technics Pages: 264

Ground Pounder GPV1000.2

Brand: Crunch Pages: 15

Brand: Ross Pages: 28

Jazz Chorus JC-90

Brand: Roland Pages: 10

Brand: McHammer Pages: 3

Brand: lb Pages: 16

Brand: unidor TRsystems Pages: 20

Brand: Lab.gruppen Pages: 31

Brand: Altronics Pages: 4

Brand: QSC Pages: 150

Brand: AudioSource Pages: 4

Brand: Audio Control Pages: 26

Brand: Arrel Audio Pages: 12

Brand: Lyngdorf Audio Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands