Telonics MINI-12 User Manual Download Page 50 | Manualshive

Page: 50 / 62

background image

Telonics TCA-500C Combo Amp

50

PB-009289 Rev E

T

ELONICS

T

ILT

-B

ACK

F

OOT

A special Telonics – designed Tilt-Back Foot is provided on the following Models:

TCA-500B&C & Combo Amps
TCA-500B&C Mini-Combo Amps
External Speaker Cabinets for TCA-500B&C Mini-Combos

The Tilt-Back Foot is designed to tilt the
amplifier slightly backward to enhance
visibility of the control panel.  To deploy
the Foot, rock the amplifier backward and
pull downward on the tip of the foot until
it locks into place.

To retract the foot, rock the amplifier
backward sufficiently to remove any
weight on the foot. Push the tip of the Foot
back and upward until it is heard to snap
into its cavity on the bottom of the
amplifier cabinet.

Do Not Attempt to Stand on the
Amplifier Cabinet with the Foot
Deployed!

«
...
48
49
50
51
52
...
»

Summary of Contents for MINI-12































































Reviews:

No comments

Related manuals for MINI-12

Brand: JBL Pages: 20

Brand: Cable Electronics Pages: 2

Brand: NAD Pages: 18

Brand: NAD Pages: 2

Brand: Hama Pages: 8

Brand: Barcus-Berry Pages: 2

Brand: rabbitone Pages: 2

Brand: QUAD Pages: 4

Brand: QSC Pages: 142

SU-Z65 - SERVICE

Brand: Technics Pages: 20

Brand: Transistor Pages: 44

Brand: Hyundai Pages: 17

Brand: Parasound Pages: 14

Brand: Baja Pages: 20

Brand: ValveTrain Amplification Pages: 7

Brand: FAME Pages: 8

Brand: Extron electronics Pages: 2

Brand: Hyundai Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands