Telematrix 2 Line trimline User Manual Download Page 15 | Manualshive

Page: 15 / 22

background image

Ringer Volume Control Switch

There are two (2) slide switches located on the left

side of the base unit that is used to adjust the loudness
of the ringing sound. A “low” and “high” setting
are provided . Select the desired loudness by
sliding the switch in the appropriate position.

14

SWITCH SETTINGS

«
...
13
14
15
16
17
...
»

Summary of Contents for 2 Line trimline























Reviews:

No comments

Related manuals for 2 Line trimline

Brand: NEC Pages: 144

Brand: Jacob Jensen Pages: 32

Brand: Xblue Networks Pages: 32

Brand: TIE Pages: 28

900 MHz Digital Spread Spectrum Dual Keypad Cordless Telephone with Caller ID/Call Waiting...

Brand: Radio Shack Pages: 24

Brand: Talkaphone Pages: 8

Brand: DAINCUBE Pages: 35

ClearSound CC40

Brand: Geemarc Pages: 24

Brand: Geemarc Pages: 73

Brand: Trident Voice Pages: 2

Brand: Brother Pages: 10

Brand: Doro Pages: 20

SP5050 - Bluetooth hands-free Speakerphone

Brand: Jabra Pages: 14

DX14560 DX14561

Brand: Uniden Pages: 12

SoundStation IP

Brand: Polycom Pages: 4

Brand: 101VOICE Pages: 2

Brand: Microframe Corporation Pages: 13

Brand: Lucent Technologies Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands