Telematrix 2 Line trimline User Manual Download Page 17 | Manualshive

Page: 17 / 22

background image

Message Waiting Switch

This telephone is standard equipped to support

   eight high voltage (90VDC Neon) or low voltage
   (LED) Message  waiting systems, A selector
   switch is provided underneath the faceplate for
   security. The options are:

   NEON = 90 VDC NEON
   LED = LOW VOLTAGE

   Note: The switch is factory set to the “Neon”
   position.

16

SWITCH SETTINGS

«
...
15
16
17
18
19
...
»

Summary of Contents for 2 Line trimline























Reviews:

No comments

Related manuals for 2 Line trimline

Brand: Panasonic Pages: 8

Brand: Dai Telecom Pages: 21

DXAI5688-2 - DXAI Cordless Phone

Brand: Uniden Pages: 68

Brand: Uniden Pages: 72

Brand: Yealink Pages: 4

Brand: AT&T Pages: 33

Brand: Uniden Pages: 8

Brand: VTech Pages: 2

Brand: Uniden Pages: 52

DECT1725 Series

Brand: Uniden Pages: 44

Brand: Northland Pages: 7

Brand: Uniden Pages: 36

Brand: AT&T Pages: 36

Brand: Uniden Pages: 32

Brand: Bridgesecure Technologies Pages: 4

VoiceSonic VB-42210

Brand: Panasonic Pages: 40

Link2Cell KX-TGD862

Brand: Panasonic Pages: 89

Brand: Unifat Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands