background image

 
 

 

 

 

WEBS-MT/R Tower Installation Instructions 

 

 

Copyright 2011 Talk-A-Phone Co.  All rights reserved. 

Rev. 10/19/2011

 

Talk-A-Phone Co. 

• 7530 North Natchez Avenue • Niles, Illinois 60714-3804 

Phone 773.539.1100 • Fax 773.539.1241 • [email protected] • www.talkaphone.com

 

All prices and specifications are subject to change without notice. 

Talk-A-Phone, Talk-A-Lert, Scream Alert and WEBS are registered trademarks of Talk-A-Phone Co. 

 
 
 

I.  Introduction 

This manual is for tower installation only.  For instructions on installing the anchor bolts into the 
foundation, see the ETP-MT/R Anchor Bolt Installation Instructions. 

II.  Contents 

Before beginning installation, make sure you have all the included components. Each 

WEBS-MT/R

 tower 

consists of the following packages.  Package #1 contains the 

WEBS-MT/R

 tower itself.  Package #2, 

labeled 

MT/R BOLT KIT

 contains the anchor bolt install kit. Package #3, labeled 

TOWER PTS

, contains 

the tower hardware and lighting installation kit. Package #4, labeled 

WEBS-MT/R-KIT

 contains the WEBS 

paging kit. Package #5, labeled 

WEBS-BACKUP

 (sold separately) contains the WEBS power back-up kit. 

Emergency phones are sold and shipped separately (with mounting screws included). 

 

 

 

MT/R BOLT KIT

 

QTY  Part Number 

Description 

42838 

J-Bolts 

26312 

Cardboard Template 

 

TOWER PTS 

QTY  Part Number 

Description 

42839 

3/4"-10 Hex Nut 

42840 

3/4" Washer 

42841 

10-24 x 3/4" Pan Head Tamper-proof Screw 

42843 

6-32 Hex Nut 

67478 

Polycarbonate Light Cover 

68590 

LED Faceplate Light 

 

LED Blue Light 

 

WEBS-MT/R-KIT

 

QTY  Part Number 

Description 

83075 

WEBS Loudspeaker 

NA 

Terminal Blocks on DIN rail 

68605A 

Local Paging Microphone  

68635 

Paging Amplifier 

WEBS-VCU 

WEBS-Volume Control Unit 

19667 

RCA Audio Cable 

4247 

8-32 x 1/2” Slotted Pan Head Screw 

42847 

8-32 Hex Nut 

67475 

Gel-filled wire nut 

86394 

Power Supply 12VDC (not included if WEBS-BACKUP is used) 

 

Summary of Contents for WEBS-MT/R









Reviews: