background image

PCI Express 3.0 - CrossSync PHY and Compliance Test Capable

Recommended Oscilloscope Probes

Oscilloscope Software Options

The Oscilloscope Software options allow you to enable CrossSync PHY functionality on installed CrossSync software.

Recommended Oscilloscopes

CrossSync PHY is compatible with all LabMaster 10 Zi and WaveMaster 8 Zi series oscilloscopes. Below are some 
recommendations for example test configurations.

PCI Express 4.0 - CrossSync PHY and Compliance Test Capable

Product Description

Product Code

13 GHz (or higher), 40 GS/s, 4ch, 64 Mpts/Ch Serial Data Analyzer
with 6.5 Gb/s Serial Trigger, 8b/10b and 64b/66b decode.

SDA 813Zi-B

Product Description

Product Code

High-speed Data Signals

8 GHz differential probe with ProLink interface

DH08-PL

13 GHz differential probe with ProLink interface 

DH13-PL

16 GHz differential probe with ProLink interface 

DH16-PL

20 GHz differential probe with ProLink interface 

DH20-PL

25 GHz differential probe with 2.92 mm interface

DH25-2.92MM

30 GHz differential probe with 2.92 mm interface

DH30-2.92MM

Rail Voltage/current Points

Power/Voltage Rail Probe. 4 GHz bandwidth, 1.2x attenuation, ±30V offset, ±800mV

RP4030

Product Description

Product Code

CrossSync PHY option for LabMaster 10 Zi - sync oscilloscope with PCIe Protocol Analyzer hardware 

 

LM10Zi-CrossSyncPHY-PCIe

CrossSync PHY option for WaveMaster 8 Zi - sync oscilloscope with PCIe Protocol Analyzer hardware

 

WM8Zi-CrossSyncPHY-PCIe

Product Description

Product Code

25 GHz (or higher), 80 GS/s, 4 Ch, 32 Mpts/Ch LabMaster 10 Zi Acquisition Module

LabMaster 10-25Zi-A

LabMaster Master Control Module 

LabMaster MCM-Zi-A

Summary of Contents for PCI Express Gen4 M.2















Reviews: