Telect BCS II SIMPLEX User Manual Download Page 16

Page: 16 / 17

Telect, Inc. • USA +1.509.926.6000 • 52.33.3836.37.52
www.telect.com • © 2010 Telect, Inc., All Rights Reserved, 117209-1 A0

Page 13

Figure 9 - Inserting the LED

4. When the LED snaps into place, the installation is complete.

5. To test the new LED, insert a plug into the “M” (monitor) jack.

The LED flashes for about 30 seconds, then lights steadily.

This procedure is complete.

4.1.2 In Case Of Difficulty

If problems occur after initial installation, check all cable connections and the installation
instructions in Chapter 2.

4.1.2.1 Technical Support

By e-mail: [email protected]
By phone: 888-821-4856 or 509-921-6161

4.1.3 In-Warranty Service

Contact your Telect equipment distributor, or call a Telect Customer Service Representative:

1-800-551-4567
1-509-926-6000

Telect will repair or replace defective products within the limits of the warranty. See “Repacking
for Shipment” in this section.

NOTE:

Call a Customer Service Representative for a Return Material Authorization (RMA) before

returning any equipment.

4.1.4 Out-Of-Warranty Service

The procedure for out-of-warranty service is the same as for in-warranty service, except that
Telect charges a processing fee, and you must submit a Purchase Order along with a Return

Flat surface of LED to
flat surface of socket

Leads

LED

Summary of Contents for BCS II SIMPLEX


















Search results

Summary of Contents for BCS II SIMPLEX

Reviews:

Related manuals for BCS II SIMPLEX

Brands by name

Popular brands

Telect BCS II SIMPLEX, User Manual

Search results

Summary of Contents for BCS II SIMPLEX

Reviews:

Related manuals for BCS II SIMPLEX

Brands by name

Popular brands