Tektronix 310A Instruction Manual Download Page 61

Page: 61 / 132

Performance Check/Calibration—

Type 310A

Fig. 5 -6 . Lo cation o l A S T IG ad justm ent (rear panel).

C H E C K -T he trace should be parallel to the center

horizontal line w ith in 0.5 division/10 divisions (i.e., w ith

trace  positioned  to center horizontal  line at the farthest  left
vertical  line  o f  the  graticule,  the  trace  must  be w ith in   0.5
division  o f  the  center  horizontal  line  at  the  farthest  right

vertical line).

d. A D JU S T -Loosen the CRT base clamp w ith the

Phillips screwdriver. Push the CRT forward so the CRT face
is firm ly against the external graticule. Then rotate the CRT

u n til the trace is parallel to the center horizontal line and

re tighten the base clamp.

e. Disconnect the patch cord. Close and latch the swing

out chassis.

N O T E S

5-11

Summary of Contents for 310A





































































































































Search results

Summary of Contents for 310A

Reviews:

Tektronix 310A, Instruction Manual, Page: 61 / 132

Search results

Summary of Contents for 310A

Reviews: