background image

EM00136064                                                                           rev. 2.1 

6

Display during Operation 

Display during Setting (MODE key) 

Timer  

F

F

F

      7,0 ml 

      Stop     P 0%

 

Operating mode 

• 

Timer        

 

 

Alarms and statuses 

• 

Liv = level alarm 

• 

Flow = flow alarm or 
….Release wait 

FLOW  

sensor status 

Programmed value 

• 

Quantity in ml 

Pump status 

• 

Dry = pump starting up 

• 

Stop = pump stop 

• 

Restart = pump restart 

Value of the dosing in 
progress 

• 

Percentage of 
strokes/min 
max 

 

Q.tà         20,0ml 
 20,0ml      P 100% 

Operating mode 

• 

The following are shown in sequence: 
quantity to dose, delay in d.hh.mm. 
and interval in d.hh.mm 

Dosing value 

• 

Programmed 
quantity in m

l

 

Value of the dosing percentage, 
which can be modified by 
pressing the + or – keys 

 

 
Paragraph 3 – Timed Dosage 

(Frequency signal input “TRIGGER” not activated)

 

Programming Operation 

+

-

-

-

-

+

-

+

-

+

-

Tempo

Quantity    100ml

Delay     0.01.50

Interval   0.01.50

PROG

Time

Time      g.hh.mm

Time      g.hh.mm

Configuration

Pum functions

Configuration

Pum functions

-
-

Trigger Mode

Pause Input Mode

Disable

Restart Timer

+

-

-

Pause Input Mode

Restart Timer

-

Pause Input Mode

Freeze Time

Pause Input Mode

Pause Dosing

 

The pump doses a programmed quantity in ml. It is possible to set a 
pump delay time (

Delay

) when the pump is started and an interval 

between two successive dosings (

Interval

), as illustrated in the 

diagram: 
 
 
 
 
 
 
 
 
 
The 

Delay

 and 

Interval

 times are in dd.hh.mm (days, hours, 

minutes) 
 
The 

Pause

 input can be programmed in three different modes: 

1. 

FreezeTime:

 when the pause is activated, the system cuts 

out the current time count and restarts it when the pause is 
deactivated. 

2. 

Pause Dosing:

 with the pause activated, the system 

continues to count time the and stops the dosing. 

3. 

Restart Timer

: when the pause is activated, the system 

stops the dosing and when the pause is deactivated the 
count starts again from the beginning. 

Durante la fase di funzionamento della pompa, è possibile 
modificare la frequenza di dosaggio premendo 

contemporaneamente i tasti 

  

 per aumentare la frequenza 

oppure i tasti 

  

 per diminuirla.

 

 

Display during Operation

 

Display at start-up (MODE key)

 

Timer  

F

F

F

      7.0 ml

Liv    Stop    P 0%

 

Operating mode 

• 

Timer

 

 

• 

Alarms and Level 
statuses = level alarm 

• 

Flow = flow alarm 

FLOW 

sensor 

status 

Programmed value

• 

Quantity in ml 

Pump status 

• 

Dry = pump starting up 

• 

Stop = pump stopping 

• 

Restart = pump restarting 

Value of dosing in 
progress: 

• 

Percentage of 
strokes/min max

 

 

Q.tà         20,0ml   

20,0ml

P 100%

Modalità di funzionamento 

 

Vengono visualizzati in 
sequenza:quantità da 
dosare, ritardo in g.hh.mm e 
intervallo in g.hh.mm 

Valore del dosaggio 

 

Quantità 
programmata in 
ml 

Valore della percentuale di 
dosaggio, modificabile premendo 
sui tasti + o - 

 

 
 

Delay 

Interv.

Quantity 

Summary of Contents for TCK










Reviews: