Technalogix tp400d-8vsb User Manual Download Page 26 | Manualshive

Page: 26 / 42

background image

26

PIC-3.4-13

This page shows the Input ASI information. There are two channels available to receive

ASI streams: ASI1 and ASI2.

Area1

: set the ASI parameters, include Enable and TS Standard.

Enable

: enable / disable the ASI channel to receive input stream.

TS Standard

: select the correct TS standard: DVB or ATSC

Area2

: displays the programs list of the input stream. You can get the programs list by

clicking the ScanTS (ASI1) and ScanTS (ASI2).



IP

PIC-3.4-14

From this page, you can setup the device’s local IP parameters (Area1) as well as the

TSIP ports’ output parameters (Area2 and Area3). There are two TSIP channels

available for receiving IP streams.

Area 1

Area 2

Area 3

Area 1

Area 2

«
...
24
25
26
27
28
...
»

Summary of Contents for tp400d-8vsb











































Reviews:

No comments

Related manuals for tp400d-8vsb

Brand: Landoll Pages: 34

Brand: Garmin Pages: 10

Brand: Naviom Pages: 31

Brand: iFIT Pages: 11

Brand: M-Audio Pages: 12

Brand: M-Audio Pages: 64

Brand: M-Audio Pages: 16

Brand: M-Audio Pages: 4

Brand: M-Audio Pages: 52

Brand: Velp Scientifica Pages: 16

Brand: Velp Scientifica Pages: 2

Brand: Velp Scientifica Pages: 32

Brand: Velleman-Kit Pages: 32

MiniLift160 Classic

Brand: Handicare Pages: 28

Brand: Hands Free Farm Pages: 24

Brand: i-Optik Pages: 75

Brand: VelociRAX Pages: 4

Brand: ABM Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands