I
UK
D
E
F
NL
P
S
DK
FIN
B
GR
CZ
EE
LV
LT
H
M
PL
SK
SLO
11
Operator's guide
7. CONNECTION TO THE MAINS
1
2
3
4
5
N.B.:
8. CONTROLS
1. Cover lifting switch:
2. Light switch:
3. Refrigeration switch:
4. Thermometer
Thermostat:
5
“
SET or P
”
6
“
UP
”
7
“
DOWN
”
9. CHECKING CORRECT OPERATION
Make sure that: 1.
2.
3
4
5.
6
10. INTERNAL CLEANING
1.
2.
3.
4
5
11. REPLACEMENT OF THE LAMP (VT-VTL)
1
2
3.
4
5
6
7
. Ensure that mains voltage and frequency are the same as those stated on the rating plate (A) attached
to the appliance. . Ensure that the supply socket:
.
Ensure that there is no danger of explosion (AD) in the room. . Make sure the environment is suitable for
the power supply cable provided. The cable of the appliance is H05 VVF, designed for internal use.
. Insert the plug in the socket (do not use three-way adapters and reduction adapters).
if the
equipment has been transported or stored overturned, let is rest in its correct position for at least 3 hours
before hooking it up to the mains (see fig. 5).
The appliance features controls situated in a protected panel on the front side.
to
open and close the cover - Position II to lift - Position O to stop - Position I to lower.
to
switch on the internal lights.
to switch on the refrigeration unit.
: to read the temperature in the counter.
to adjust the temperature setting.
a) Press key
to display the temperature set-point, which can be changed by pressing key
or
(see fig. 6).
the plug is connected;
the refrigeration unit switch is on (green light lit up);
. thermometer shows the desired temperature for the goods to be stored; . appliance is not exposed to
direct sunlight or to powerful lamps;
ambient temperature does not 30°C with 55% R.H.
(climatic class 4); . there are no direct air draughts in the appliance, coming from the appliance itself,
owing to the presence of doors, windows, fans or conditioner outlets.
Switch off the appliance.
Check the evaporator fins for frost or ice. Should the layer of frost be too
thick, and ice drips are noted that could impair passage of air, complete defrosting should be undertaken.
Remove goods and store them in another suitable refrigerator running at the same temperature.
Remove the plug in the bottom section of the machine. . Clean the walls and accessories with a
sponge dipped in water and sodium bicarbonate. Take care not to touch the evaporator fins, which
feature sharp edges. . Dry all parts with care and refit all components. Refit the plug before turning on
the appliance.
. Open the cover. . Switch off the appliance.
Remove the screws securing one of the lamp sockets in
place. . Remove the lamp socket, whilst holding the fluorescent tube and its protective cover. . Pull the
protective cover out of the other lamp socket. . Replace the fluorescent tube. . Refit all components by
following the above instructions in reverse order (see fig. 7).
a)
b)
c)
is properly earthed;
fulfils the requirements of the
rated current as set out on the rating plate;
complies with the IEC regulations:- thermal-magnetic
switch with In = rated value as stated on the rating plate; - differential with Id sensitivity = 30 mA.
Summary of Contents for BRINA INOX
Page 4: ...I UK D E F NL P S DK FIN B GR CZ EE LV LT H M PL SK SLO 4 VT INOX 5 6 4 1a...
Page 21: ...I UK D E F NL P S DK FIN B GR CZ EE LV LT H M PL SK SLO 19 FIG 1 FIG 3 VT INOX...
Page 27: ...I UK D E F NL P S DK FIN B GR CZ EE LV LT H M PL SK SLO 25 4 1 16 2 5 4 1 16 2 5 20 S G C...
Page 30: ...I UK D E F NL P S DK FIN B GR CZ EE LV LT H M PL SK SLO 30...
