background image

28

TEC-67398-2

 

Technical description Prizrak-5S BT

Annex №4

Engine 

compartment unit HCU-230/BT adjustment (menu 20)

The HCU-230/BT module (hereinafter: the module) was designed for connection to an optional equipment which 

is mounted in the engine compartment. The communication between the HCU and the main immobilizer module is 

carried out via the channel allowing to avoid running the cables from the main immobilizer module into the engine 

compartment.

Pairing the 

HCU-230/BT module

Registration consists in pairing the hood compartment unit with the immobilizer system. Once the HCU module 

has been paired it is not possible to register it into another immobilizer or alarm system until the previous registra-

tion is voided (refer to the «Cancelling registration of the HCU-230/BT module»).

Pairing the module using the TECprog2:

1. 

Install the immobilizer system and the HCU on a vehicle and supply power to the modules. 

2. 

Run the TECprog2 and connect to the Immobilizer system via USB or Bluetooth (using the TEC-prog USB 

Bluetooth adapter), follow the instructions.

Pairing through the programming button and programming menu

In case if a hood compartment module has already been paired with the immobilizer system then after a new 

module is registered into the immobilizer — the previous registration will be deleted from memory. After that the 

immobilizer system will only recognize and communicate with the newly registered HCU-230 module. All adjust-

ments and configurations are carried out using the programming button (hereinafter — PB). During the program

-

ming process the immobilizer performs indication by audible beeps (hereinafter — beeps). It is allowed to enter PIN 

code «2» with the programming button if a vehicle hasn't yet travelled 10 km after installing the system and the 

default PIN code hasn't been changed. The immobilizer system will automatically exit the programming mode if at 

any programming step the ignition is switched OFF or if within 10 seconds after the last action the brake pedal is 

not pressed.

1.  Supply power to both devices (pairing is available within 2 minutes after supplying power to the modules).

2.  Switch the vehicle’s ignition ON. Carry out an authentication procedure.

3. 

Within 10 seconds enter the programming menu:

•  press the programming button 20 times;

• 

10 beeps following after that confirm that the manu has been successfully entered. A different number of 

beeps signifies an error.

4. 

Select the menu option «Hood compartment unit HCU-230/BT registration»:

•  press the PB — 1 time.

• 

confirmation — 1 beep.

5. 

To verify the module registration status:

•  press and hold the brake pedal;

• 

confirmation: 1 beep 

— the HCU module is registered; no audible indication — the module is not registered.

6. 

To pair (register) the module:

•  press the PB one time.

• 

the  immobilizer  system  starts  searching  for  an  HCU-230  module,  this  will  be  accompanied  by  short 

intermittent beeps.

• 

the  registration  will  begin  automatically  as  soon  as  the  module  is  detected,  the  beeps  frequency  will 

change.

• 

the immobilizer will emit a long warning beep in case if it detects two or more modules. The registration 

will cancel automatically. Wait at least 2 minutes. Repeat the procedure.

7. 

Successful registration is followed by the confirmation trill and a short single repeating beep indicating that 

one module has been registered.

8. 

To finish the registration process: release the brake pedal and switch OFF the ignition. Confirmation trill will 

sound.

Summary of Contents for Prizrak 5S/BT

































Reviews: