22
TEC-67398-2
Technical description Prizrak-5S BT
Configuring the custom settings (Menu 12)
Table 9.
User settings (Menu 12)
The code to enter the menu — «12», twelve presses on the programming button, confirmation — 4 short beeps).
The devault values are highlighted.
№
Option descriptiom
Default
values
Available values/ Notes
1 Immobilizer
1
1 — ON;
2 — OFF
2 AntiHiJack
1
1 — ON;
2 — OFF
3 Travel distance before AntiHiJack
triggers
1
Range from
1
to 10.
The default setting is 1-means
100 meters, 3-300 meters
4 Audible confirmation after
authentication
1
1 — ON;
2 — OFF
5 Service (valet) mode automatic
disabling
1
1 — ON;
2 — OFF
6 Automatic door lock
2
1 — ON;
2 — OFF
7 Automatic door unlock
2
1 — ON;
2 — OFF
8
Windows, side mirrors, sunroof auto
-
matic closure («Comfort»)
4
1 — Windows closure; 2 — windows and side mirrors
closure; 3 — windows and sunroof clo sure;
4 — win-
dows, sunroof closure, side morrors folding;
5 — OFF
(closure is not performed)
9 Authentication method
(PUK code required)
1 or 3
1 — Slim-tag (for Prizrak 5S/Slim and Prizrak
5S/2Slim);
2 — PIN code;
3 — Slim-tag or PIN code
(for Prizrak 5S);
4 — Slim-tag and PIN code
10 New tag registration
—
The number of beeps (when the brake pedal is
pressed) indicates the total number of registered
Slim-tags (from 0 to 8)
11 Tags detection quality test
—
Allows to determine zones where a tag is detected better
12 AntiHiJack feature automatic deacti-
vation with a tag
2
1 — ON;
2 — OFF
13 Removing smartphone-tags from
memory
—
From 1 to 4. The number of beeps equals to the number
of registered smartphone-tags (from 1 to 4)
14
Deleting all Slim-tags from memory
—
The number of beeps equals to the number
of registered Slim-tags (from 1 to 8)
Programming sequence
The entire programming process is carried out through the programming button (hereinafter referred to as -
PB). The immobilizer emits audible signals (hereinafter
—
beeps) to indicate the current state of a setting being
programmed. In case if the option number or the option value consists of a two-digit number, the beeps will sound
as follows: the first digits are indicated by long beeps, the second digit- by short beeps. For example: the figure
12
—
will be indicated by one long beep and two short beeps; 25
—
two long and 5 short beeps. It is allowed to en-
ter PIN code «2» with the programming button if a vehicle hasn't yet travelled 10 km after the installation and the
default PIN code hasn't been changed. The immobilizer system will automatically exit the programming mode if at
any programming step the ignition is switched OFF or if within 10 seconds after the last action the brake pedal is
not pressed.
1. Switch the vehicle’s ignition ON. Carry out an authentication procedure.
2.
Not later than in 10 seconds enter the programming menu:
•
press and release the programming button 12 times.
•
confirmation
—
4 beeps. A different number of beeps signifies an error.
3.
Select a desired menu option:
•
press and release the programming button the number of times corresponding to the option number in
the menu. Each time the button is pressed the option number is increased by one. The option numbers are
changed in rotation, after the last option number goes the first one;
4. To find out the current option value:
•
press and hold the brake pedal;
•
the emitted beeps will indicate the current option value.
5.
To change the value of the option:
•
keep the brake pedal down. Each time the button is pressed the option number is increased by one. The
option numbers are changed in rotation, after the last option number goes the first one.
6. To configure the value of another option-release the brake pedal. This will bring you back to the step 3 of the
programming sequence. To exit the programming mode — switch the ignition OFF.
